Blog

Addendum BLOG D - Connecting to the Arduino IoT Cloud directly over LoRaWAN

2022-03-04T19:22:00Z

Addendum BLOG D - Connecting to the Arduino IoT Cloud directly over LoRaWAN This blog is an addendum Blog to "Blog#2 Design (Case Enclosure Reliability Monitor)", for my Design Challenge Just Encase Blog Series. The design in BLOG#2, was ...(read more)

#Blog 5 Just Encase Challenge : Final blog with the results and enclosure conditions

2022-03-02T23:42:00Z

Hello all, If you have read this series of blogs and come along this long, that's too great. In this final blog, I would like to show the conditions of the sensors and the enclosure after two months. The ultrasonic water lev...(read more)

#Blog 4 Getting started with the airquality monitor project

2022-03-02T22:21:00Z

With the help of data that I got from the water level monitor, I was able to justify why my water usage was more than expected and found a leaking near the toilet flush which was used to discharge the water slowly to the sink and fill the flush...(read more)

#Bllog 4 Getting started with the airquality monitor project

2022-03-02T22:21:00Z

#Blog 3 Just Encase Challenge : Setup of water level sensor and demo

2022-03-01T20:50:00Z

Hello all, Finally, I was able to put everything together and started testing out the experimental setup. Wrote a code for the water level measurement and sent the data over LoRa to another module. But I was not...(read more)

#Blog 2 Just Encase challenge : Building a LoRa based water level sensor and a demo

2022-03-01T20:05:00Z

Hello all, In this blog, let's explore how we can calculate the water level using an ultrasonic distance sensor and then receive this data to my reciever node in my room. There is no internet coverage at the place whe...(read more)

#Blog1 Just Encase challenge: Getting started and deciding the architecture.

2022-03-01T13:52:00Z

Hello all, It's been a long time, I have recorded my experiments and the respective data but never got time to write blogs on the progress. Here I'm writing everything together like a series. In this blog, I'll explain...(read more)

Orb-Weaver Rover - Blog #6 - Project Overview

2022-02-28T22:38:00Z

This will be my last blog for the Just Encase Design Challenge. In this blog I'll go over the final configuration of the Rover, Sensor Boxes as well as all of the 3D models and codes associated with this project.(read more)

Just Encase Design Challenge - Winter Driving Safety (Blog 6)

2022-02-28T19:23:00Z

This blog is about surviving the cold weather if your get into an accident and have to wait for emergency personal to arrive. I was a member of Search & Rescue many years ago and know that being prepared is very important. Below are some tips I w...(read more)

Wind Turbine Health Monitoring || Moment of Truth || Blog #6

2022-02-28T14:28:00Z

Final Testing I took the wind turbine to a river nearby to test the final build, hoping for some windy weather. The setup was placed just beside the river, and the sensor node attached to it was powered by a lithium-ion battery placed inside.As soon ...(read more)

Just Encase Design Challenge - Winter Driving Safety (Blog #5 part 2)

2022-02-28T11:45:00Z

Now for part 2 of my final project. Here is the working video and photos of my completed project. Sorry for the camera movement, driving and holding the camera doesn't make for a steady video. First video is of the start-up (While driving) and s...(read more)

Blog 5: Landslide monitoring for the Himalayan region- Testing the enclosure in the field

2022-02-28T07:58:00Z

In the last blog for the Just Encase Design Challenge, I'm publishing the results and the videos of the landslide monitoring system. The enclosure box contains the electronics that detects the vibrations triggered due to the landslide and sounds ...(read more)

Just Encase Design Challenge - Winter Driving Safety (Blog #5 part 1)

2022-02-28T00:54:00Z

Here is part 1 of my final project. Below is the code and working display of my project. A lot of the live demonstration of my project can't be done due to the risk. I won't drive unsafely or get into an accident in order to show how the pro...(read more)

Orb-Weaver Rover - Blog #5 - Rover Electronics & First Moves!!!

2022-02-27T23:29:00Z

In the last blog, I showed the mechanical design and build of the rover, in this blog, I will cover the electronics in the rover and that part of the build. I'll also feature the first moves made by the rover in this blog!!!(read more)

Blog 4: Landslide monitoring for the Himalayan region- Putting it all together and testing

2022-02-27T18:38:00Z

Assembling all the parts together In this blog, I will put together all the components of the landslide monitoring system - The vibration sensor, the buzzer and the Arduino inside the enclosure box. I chose the non-transparent 1554UGY water-tight enc...(read more)