Summer of Sensors Design Challenge

Welcome to

4 Challenges, 4 Sensory Kits and 4 Ways to Win

Participate in one of our four Design Challenges for the Summer of Sensors! Contestants will be selected to receive one of four different kits, tailored to a specific theme. The winners of these individual challenges will demonstrate the best use of the SensorXplorer, bio sensors, smart asset tracking, and the best air quality application.

THE KITS & PRIZES

In the Air Tonight: Best Air Quality application using the ZMOD4510-EVK or HS4000-EVK

Buy Kit

Prize: Philips AC0820 Series 8 Air Purifier + 11" iPad Pro 128GB WiFi

TAG You’re it: Best Smart Asset Tracking using the STEVAL-SMARTAG1

Buy Now

Prize: Apple Air Tags 4 Pack + 11" iPad Pro 128GB WiFi

Exploration Station: Best use of the SensorXplorer and sensor range

Buy Kit

Prize: Garmin GPS Rugged GPS Smart Watch + 11" iPad Pro 128GB WiFi

Healing Touch: Best use of the MikroE Bio Sensors and the Arduino Uno

Buy Kit

Prize: Under Bed IoT Sleep Tracker + 11" iPad Pro 128GB WiFi

All challengers who complete their project by the submission deadline: 7th October 2022 will receive a MultiComp Pro Multimeter Set

Blog - Post List

Summer of Sensors Design Challenge - In The Air Tonight – Blog #4 (Data Acquisition)

abhayrjoshi

Challenger - ZMOD4510 - Outdoor Air Quality Sensor Hello element14 Family, In order to correctly fit the board into the case properly, I first soldered pullup resistors onto the OLED display itself. After that, I assembled all the parts at my worksta...
- 11 Nov 2022
Summer of Sensors Design Challenge - In The Air Tonight – Blog #3 (Interfacing)

abhayrjoshi

Challenger - ZMOD4510 - Outdoor Air Quality Sensor Hello element14 Family, I don't believe I could do a better job of describing the first unpacking experience and the Renesas software review than the other challengers have already done. I thus made ...
- 11 Nov 2022
Blog #5: Adding Connectivity to the Project using Renesas DA16600 Wi-Fi Module

misaz

Hello everyone. I welcome you to my 5th blog as part of my serie about ZMOD4510 Outdoor Air Quality sensor as part of Summer of Sensors Design Challenge and category In the Air Tonight category. In my first blog I described my plans as part of compet...
- 10 Nov 2022
Designing a Small Health Monitoring System for the Elderly - HMS Blog #3 - First Prototype

milosrasic98

Hi! In this blog, I will be going over the first working prototype for my project. It's still in the breadboard phase but is fully functional. Things I will cover are all of the electronics used in the project as well as the wiring between them, and the software for both the Arduino as well as the ESP8266 (Adafruit Feather Huzzah). Besides that, I will also cover how I set up a simple server using a Raspberry Pi and Node…
- 10 Nov 2022
Summer of Sensors Design Challenge - In The Air Tonight – Blog #2 (System Design)

abhayrjoshi

Challenger - ZMOD4510 - Outdoor Air Quality Sensor Hello element14 Family, After reading the following papers, I ultimately made the decision to measure noise in addition to air pollution: Impact of Noise and Air Pollution on Pregnancy Outcomes (appa...
- 9 Nov 2022
Remote Patient Monitoring System - Blog #3 : Experimenting with ECG Sensor

taifur

Table of Contents Introduction What is ECG? Why is ECG Important The AD8232 ECG Sensor AD8232 Connections Sensor Pad Placement Interfacing AD8232 Sensor with Arduino Understanding ECG Signal Conclusion Introduction This is the third blog of the&nb...
- 9 Nov 2022
In The Air Tonight - Monitoring the Outside Air

ntewinkel

It's funny how plans change when results come in that don't match the original hypotheses! Science!! My plan for this blog post had been to check the air quality in the hallway that connects to our attached garage; However, after having completed a s...
- 9 Nov 2022
IntelliLight - Adaptive Smart Bulb Controller - Part 8 - 3D Printed Case

osjef

Table of Contents Introduction Building the CAD Model 3D Printing the Model Assembling the Project Powering it Up Coming Next... Introduction This is my 8th blog in a series I am writing for the Summer of Sensors Design Challenge kindly sponsored...
- 7 Nov 2022
Remote Patient Monitoring System - Blog #2 : Experimenting with Oximeter 5 Click

taifur

Table of Contents Blood Oxygen Saturation Pulse Oximetry Oximeter 5 Click Heart Rate Measurement Oxygen Level Measurement The Oximeter 5 Click Hardware Overview Getting Started With Oximeter 5 Click Installing Library Testing the Sensor - Reading Ra...
- 7 Nov 2022
Summer of Sensors Design Challenge - Blog No. 4

me_Cris

Hello everyone! In this blog I also put the MAX30102 sensor into operation. This module incorporates a MAX30102 that can be used to measure pulse oximetry and heart-rate. It is compact, having small dimensions, and is also suitable in applications fo...
- 6 Nov 2022