In-circuit debugger/programmer for STM8 and STM32I

e14-publisher — Fri, 05 May 2023 15:48:33 GMT

Current Revision posted to Documents by e14-publisher on 5/5/2023 3:48:33 PM

In-circuit debugger/programmer for STM8 and STM32I

Manufactured By:ST Microelectronics

Part Number:ST-LINK/V2

Buy Now

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.

STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

Features

5 V power supplied by a USB connector
USB 2.0 full speed compatible interface
USB standard A to mini B cable
SWIM specific features
1.65 V to 5.5 V application voltage supported on SWIM interface
SWIM low-speed and high-speed modes supported
SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
JTAG/serial wire debugging (SWD) specific features
1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
JTAG supported
SWD and serial wire viewer (SWV) communication supported
Direct firmware update feature supported (DFU)
Status LED which blinks during communication with the PC
Operating temperature 0 to 50 °C

Ships With

SWIM Cable
USB Connector

Required Tools

Accessory Tools

Documents

Product Brief/Fact sheet

DB1275: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Revision Note

RN0084: ST-LINK/V2 firmware upgrade (pdf)

User Manual/Guide

UM1075: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Tags: emulation_debugging, debuggers_programmers, stm, st-link, mcu

In-circuit debugger/programmer for STM8 and STM32I

e14-publisher — Thu, 16 Dec 2021 23:21:25 GMT

Revision 3 posted to Documents by e14-publisher on 12/16/2021 11:21:25 PM

In-circuit debugger/programmer for STM8 and STM32I

Manufactured By:ST Microelectronics

Part Number:ST-LINK/V2

Buy Now

STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.

STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

Features

5 V power supplied by a USB connector
USB 2.0 full speed compatible interface
USB standard A to mini B cable
SWIM specific features
1.65 V to 5.5 V application voltage supported on SWIM interface
SWIM low-speed and high-speed modes supported
SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
JTAG/serial wire debugging (SWD) specific features
1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
JTAG supported
SWD and serial wire viewer (SWV) communication supported
Direct firmware update feature supported (DFU)
Status LED which blinks during communication with the PC
Operating temperature 0 to 50 °C

Ships With

SWIM Cable
USB Connector

Required Tools

Accessory Tools

Documents

Product Brief/Fact sheet

DB1275: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Revision Note

RN0084: ST-LINK/V2 firmware upgrade (pdf)

User Manual/Guide

UM1075: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Tags: emulation_debugging, debuggers_programmers, stm, st-link, mcu

In-circuit debugger/programmer for STM8 and STM32I

e14-publisher — Thu, 16 Dec 2021 03:06:48 GMT

Revision 2 posted to Documents by e14-publisher on 12/16/2021 3:06:48 AM

In-circuit debugger/programmer for STM8 and STM32I

Manufactured By:ST Microelectronics

Part Number:ST-LINK/V2

Buy Now

STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.

STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

Features

5 V power supplied by a USB connector
USB 2.0 full speed compatible interface
USB standard A to mini B cable
SWIM specific features
1.65 V to 5.5 V application voltage supported on SWIM interface
SWIM low-speed and high-speed modes supported
SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
JTAG/serial wire debugging (SWD) specific features
1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
JTAG supported
SWD and serial wire viewer (SWV) communication supported
Direct firmware update feature supported (DFU)
Status LED which blinks during communication with the PC
Operating temperature 0 to 50 °C

Ships With

SWIM Cable
USB Connector

Required Tools

Accessory Tools

Documents

Product Brief/Fact sheet

DB1275: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Revision Note

RN0084: ST-LINK/V2 firmware upgrade (pdf)

User Manual/Guide

UM1075: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Tags: emulation_debugging, debuggers_programmers, stm, st-link, mcu

In-circuit debugger/programmer for STM8 and STM32I

e14-publisher — Mon, 18 Oct 2021 20:14:45 GMT

Revision 1 posted to Documents by e14-publisher on 10/18/2021 8:14:45 PM

In-circuit debugger/programmer for STM8 and STM32I

Manufactured By:ST Microelectronics

Part Number:ST-LINK/V2

Buy Now

STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.

STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

Features

5 V power supplied by a USB connector
USB 2.0 full speed compatible interface
USB standard A to mini B cable
SWIM specific features
1.65 V to 5.5 V application voltage supported on SWIM interface
SWIM low-speed and high-speed modes supported
SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
JTAG/serial wire debugging (SWD) specific features
1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
JTAG supported
SWD and serial wire viewer (SWV) communication supported
Direct firmware update feature supported (DFU)
Status LED which blinks during communication with the PC
Operating temperature 0 to 50 °C

Ships With

SWIM Cable
USB Connector

Required Tools

Accessory Tools

Documents

Product Brief/Fact sheet

DB1275: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Revision Note

RN0084: ST-LINK/V2 firmware upgrade (pdf)

User Manual/Guide

UM1075: ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 (pdf)

Tags: emulation_debugging, debuggers_programmers, stm, st-link, mcu