Freescale i.MX 6 Development Platforms Software Download Center

Hi All,

Above download link has been fixed now.....

Regards

Ankur Tomar

Hi All,

Sorry about the inconvenience, these downloads have been corrupted and we are working on a resolution and hopefully they ll be fixed by tomorrow, we apologize for the issue.

Regards

Ankur Tomar

The above download links are not working! Can you please fix this!

the above download links are still not working?

I reset the env configuraiton using "run clearenv" and now it seems that Linux boot and the Timesys demo runs.

Thanks,

regards

Hi,

This site will help you out:

http://boundarydevices.com/u-boot-on-i-mx6/#upgradeu

Some extra information would be needed: What make and model are your board?

Hope this helps,

Dave

Hello everybody,

i installed on the microSD card the Linux Image for SABRE Lite with LCD8000-97C from the links above (using the MfgTool : mfgtools-rel-12.04.01_er_mx6q_updater).

I followed the steps in the doc : "Quick Guide of Freescale Sabre Lite Linux system V1.3.pdf", the MfgTool works fine, then i power-on the board but i see the message below from Serial console.

It seems that U-Boot desn't find the 6q_bootscript in the SD card. Can anyone help me ?

U-Boot 2009.08 (Nov 13 2013 - 11:06:28)

CPU: Freescale i.MX6 family TO1.2 at 792 MHz

Temperature:   38 C, calibration data 0x5794bf7d

mx6q pll1: 792MHz

mx6q pll2: 528MHz

mx6q pll3: 480MHz

mx6q pll8: 50MHz

ipg clock     : 66000000Hz

ipg per clock : 66000000Hz

uart clock    : 80000000Hz

cspi clock    : 60000000Hz

ahb clock     : 132000000Hz

axi clock   : 264000000Hz

emi_slow clock: 132000000Hz

ddr clock     : 528000000Hz

usdhc1 clock  : 198000000Hz

usdhc2 clock  : 198000000Hz

usdhc3 clock  : 198000000Hz

usdhc4 clock  : 198000000Hz

nfc clock     : 24000000Hz

Board: MX6Q-SABRELITE:[ POR]

Boot Device: I2C

I2C:   ready

DRAM:   1 GB

MMC:   FSL_USDHC: 0,FSL_USDHC: 1

JEDEC ID: 0xbf:0x25:0x41

Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8

SUCCESS

In:    serial

Out:   serial

Err:   serial

Net:   got MAC address from IIM: 00:00:00:00:00:00

FEC0 [PRIME]

Hit any key to stop autoboot:  0

Card did not respond to voltage select!

mmc0(part 0) is current device

MMC: block number 0x1 exceeds max(0x0)

** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **

** Bad partition 1 **

mmc1 is current device

reading /6q_bootscript

** Unable to read "/6q_bootscript" from mmc 1:1 **

Loading file "/6q_bootscript" from mmc device 1:1 (xxb1)

** File not found /6q_bootscript

MX6Q SABRELITE U-Boot >

Thanks

Trying to setup SABRE Lite with LCD8000-97C using the Linux Image from the link above. Is there a how-to guide on what needs to be done after you download the image ?

Thanks

Is there any step-by-step document to let the prebuild Android images running in Sabre-Lite with LCD8000-97C module? (Assume there is nothing in SPI NOR flash)

Thanks,

I tried to build Linux kernel with LCD patch. I could not build kernel because missing files (chip.x, ...) in the patch.

Where can I get missing files?