https://community.element14.com/products/manufacturers/bitscope/BitScope Mixed Signal Systems are programmable PC based USB and Ethernet oscilloscopes, logic analyzers, spectrum analyzers, waveform generators and data acquisition systems for Windows, Mac OS X, Linux and Raspberry Pi. They offer comprehensive solutions en-USTelligent Community 12https://community.element14.com/products/manufacturers/bitscope/f/forum/57171/hardware-troubleshooting-bitscope-442n-rev-3/237889Wed, 19 Aug 2026 01:13:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:aa07433e-cd4d-485f-af40-39f5f7fdf87dbillmaniaAfter much effort expended, I've confirmed incoming multicast datagrams are at least reaching the RTL8019AS. This was determined by observing 5 Volt square wave pulses on the RTL8019AS's pin 12 (Rx), synchronized with the datagram transmission. At the same time, The RTL8019AS's pin 13 (Tx) never budged from 0 Volts. Pin 13 is connected to Q1, which is in turn connected to R12, which finally connects to the DATA LED's minus lead. Of my three questions in the original post, 2 and 3 are now irrelevant. A schematic would still be really helpful. A troubleshooting procedure for the PIC18F 442 Network Controller would be nice, too. Otherwise, I have nothing more than some e-waste now.https://community.element14.com/products/manufacturers/bitscope/f/forum/57171/hardware-troubleshooting-bitscope-442n-rev-3Tue, 11 Aug 2026 13:55:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:87f595e8-6b59-44ec-93de-09ee93763598billmaniaI have serial BS44501-1409003. The board is labeled "Bitscope 442N Rev 3". It has two removable modules. The first is labeled "BitScope Network Controller LIA BootLoad" and the second is "BitScope VM-445N (C) 2008 Metachip". The symptoms of the board are: - the external power LED is lit steady - at power up, the Data LED blinks and then stays off - at power up, the Link LED lights after a few seconds, and stays lit - sending UDP multicast 230.10.10.10 port 16385 on the LAN does NOT blink the Data LED - no network traffic is emitted by the BitScope - other hosts on the same LAN do receive the UDP multicast datagrams - X1 pin 1 has 5 VDC - X1 pin 5 has 5 VDC I have at least three questions: 1. how can I get a schematic for this board 2. what is the manual "force reset" mechanism for this board 3. what are the definitions of the 7 pins at X1bitscopehttps://community.element14.com/products/manufacturers/bitscope/f/forum/56508/bitscope-install-under-lm22-2-missing-libpango1-0-0/234821Sun, 05 Apr 2026 14:00:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:8b3234aa-e555-4b09-bc68-4f2c76771b1aTechnixe_Perhaps somebody is interested in another way of successful install under mint 22.2: sudo dpkg -i --force-depends /path2bitscope/bitscope-dso_2.6.EA17H_amd64.debhttps://community.element14.com/products/manufacturers/bitscope/f/forum/56302/has-anyone-got-a-copy-of-the-bitscope-files-for-the-raspberries/234815Sun, 05 Apr 2026 00:31:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:6572b006-4616-4292-938c-1b8c7489382dheliocoelhojrthanks a lot !https://community.element14.com/products/manufacturers/bitscope/m/files/151057Fri, 20 Mar 2026 18:07:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:a6ee656e-f878-4d7b-b56b-af835b0437a7tm_stumpContents: bitscope-dso_2.3.BD18D.zip bitscope-logic_1.0.BG15A.zip bitscope-meter_1.2.BA28A.zip DataFiles-02.zip LIAComms-01.zip LIAComms-02.zip PICuP.zip WavePOD-01.zip bitgenlib_1.0.AK10A_i386.deb bitgenlib-apps_1.0.AK10A_i386.deb bitlib_1.4.AK19C_i386.deb bitlib-apps_1.4.AK19C_i386.deb bitscope-chart_1.0.BA28A_i386(2).deb bitscope-chart_1.0.BA28A_i386.deb bitscope-chart_1.0.BE03A_i386(2).deb bitscope-chart_1.0.BE03A_i386.deb bitscope-dso_2.2.AI08E_i386.deb bitscope-dso_2.3.BD18D_i386.deb bitscope-logic_1.0.BG15A_i386.deb bitscope-meter_1.2.BA28A_i386.deb bitgenlib_1.0.AK10A.tar.gz bitgenlib-apps_1.0.AK10A.tar.gz bitgenlib-src-1.0.AK10A.tar.gz bitlib_1.4.AK19C.tar.gz bitlib-apps_1.4.AK19C.tar.gz bitlib-src-1.4.AK19C.tar.gz bitscope-chart_1.0.BA28A.tar.gz bitscope-chart_1.0.BE03A.tar.gz bitscope-dso_2.2.AI08E.tar.gz bitscope-dso_2.3.BD18D.tar.gz bitscope-logic_1.0.BG15A.tar.gz 001_bs-pm-01.pdf bitgenlib_1.0.AK10A.zip bitgenlib-src-w32-1.0.AK10A.zip bitlib_1.4.AK19C.zip bitlib-src-w32-1.4.AK19C.zip bitscope-chart_1.0.BA28A.zip bitscope-chart_1.0.BE03A.zip bitscope-dso_2.2.AI08E.zipbitscopehttps://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/234523Thu, 19 Mar 2026 20:21:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:3a62816a-5b1e-4c4c-83f8-9dc038d628b5tm_stumpHi. Here's a zipped file with all the bitscope apps from a disc I found tucked away with an old laptop from 2011. bitscope applications from 2011 I think the i386 apps are in there, I don't know if the file will go through even though it meets the size requirements here. Let me know if these work. Looks like the site mangles the text vs dowload. tmhttps://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/233927Sun, 22 Feb 2026 02:33:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:a57cb1de-48b9-4a9f-bde2-e1efbf548a30bitscope666310 I can't say for certain it was an 'official' floppy .. but mine came with one nonetheless somehow. files are dated 2008 ?https://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/233926Sat, 21 Feb 2026 22:50:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:857ca087-a958-41b1-9427-7f6ef389fd7bbeacon_daveWhich model came with a floppy ?https://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/233925Sat, 21 Feb 2026 22:05:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:4c0376e7-0a64-4ccd-ab35-02c95a55d57bbitscope6662hours wasted unfortunately that floppy is no longer fully readable 2 files on it, drivers zipped and dso1.3 zipped, and dso is damaged i might attempt retries on other floppydrives ..but .. i doubt that'll make a difference which also poses a little problem for myself .. have a little laptop which i used to run the dos-version on (i really rarely use scope)https://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/233923Sat, 21 Feb 2026 19:55:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:d37cb195-d727-47eb-a56f-464d9761c2e4bitscope666I might actually have some files for i386, the original floppy that came with my Bitscope, but I'll have to find a floppydrive first (should have one somewhere) etc. hang on ..https://community.element14.com/products/manufacturers/bitscope/f/forum/56634/bitscope-files-for-i386-windows/233915Sat, 21 Feb 2026 10:58:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:b795bff4-bb2c-43e0-ba38-0bd0393b66c8dolesandouyeshttps://community.element14.com/products/manufacturers/bitscope/f/forum/56655/bitscope-stuff/233657Thu, 12 Feb 2026 00:15:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:4b92398c-189a-4bc4-b4fa-93a9192e9de3tm_stumpI'm not sure where to post a reply to all but here it is. Thanks for posting all the links and info. Lot's of good info here and I'll wade through as much as I can to find some answers. Found some schematics here and from a link that popped up to Silvertone Electronics also in Australia. They had/have some Bitscope products still on their site and also had a good amount of documentation. I must have one of the latest versions of the BS10 Mini as none of the pics match the version I have. As I browse through some of the pics I can see the evolution of the product. Two pics are attached with three components outlined in the lower left corner of pic #1. The SOT23-5 component has an A0P or AOP marking and only the A(zero)P shows up in my old SMD Identification catalog as a 'voltage monitor/detection' chip. This thing is roasting hot over 200 degrees F with an IR cam, plugged in with no activity and no connection. The two associated resistors are both less that half of the marked values. I can replace the resistors but I need to positively identify the 5 pin to get a replacement. I'm not sure how much time I'll spend trying to get the thing to work again, but once I attack the board for component replacement that time might get shortened in a hurry. Thanks again.https://community.element14.com/products/manufacturers/bitscope/f/forum/56655/bitscope-stuff/233605Wed, 11 Feb 2026 11:28:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:7b5b6bf8-d337-4b1f-a7f5-809b3d75fd09JWxin addition, here ( https://opentracelab.github.io/website/hardware/mixed-signal-devices/bitscope-bs10/#schematics ) there are pretty good photos of the PCB with part numbers generally visible (if some badly damaged part needs to be identified)https://community.element14.com/products/manufacturers/bitscope/f/forum/56655/bitscope-stuff/233597Wed, 11 Feb 2026 10:02:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:06a70235-3963-4766-a646-307b16ce974cmichaelkellettWow - complete schematic from 2000 ! tm_stump has all the info to fix it if they can get the bits - hope its not the the LSI1016 that's gone - they were made obsolete in 2010. It may still be obtainable. The design is very dated now - possibly not worth a great deal of effort because there are cheap micros that can out-perform it. MKhttps://community.element14.com/products/manufacturers/bitscope/f/forum/56655/bitscope-stuff/233596Wed, 11 Feb 2026 09:24:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:2c137fd1-43cb-4f2d-bf5d-93325a14becbJWxwebarchive keeps some documentation: web.archive.org/.../https://community.element14.com/products/manufacturers/bitscope/f/forum/56655/bitscope-stuffTue, 10 Feb 2026 19:00:00 GMT93d5dcb4-84c2-446f-b2cb-99731719e767:fe4636f0-110c-4645-ad2b-b2e504a9f955tm_stumpThere is some info in here about the Bitscope saga but my BS10 mini won't connect and I'd like to repair the thing. Is there a schematic available anywhere for the Mini. I thought I saw schematics on the original Bitscope site and I think I may have downloaded those but apparently my filing system is so secure that I can't find any downloads I may have made. I may have found the issue but I can't identify the IC I think is causing the problem without a schematic. Thanks, Tony