Have a Question About the Sudden Impact Design Challenge? Ask it here!

doctorcdf over 10 years ago

Please direct any questions about the Sudden Impact design challenge to this discussion thread.

Top Replies

Robert Peter Oakes over 10 years ago in reply to hawkeyethehacker +3

Post what you have, that is better than nothing. No one expects everyone to get all they set out to do completed, we all have different skill levels and time available, I did not get every single thing…
doctorcdf over 10 years ago +3

Good morning - In light of recent events, we have adjusted the following terms of the competition - The final submission date is Friday, May 8th, 2015 . We expect a minimum of 6 blog posts about each project…
kas.lewis over 10 years ago in reply to hawkeyethehacker +2

Hopefully, I was starting to give up on the kit and was just going to do my own implementation using TI parts and ADI sensors that I already have. Hopefully that won't be necessary. For now though I am…

0 doctorcdf over 10 years ago

Good morning -

In light of recent events, we have adjusted the following terms of the competition -

The final submission date is Friday, May 8th, 2015.
We expect a minimum of 6 blog posts about each project between now and the final submission date.

Thanks in advance.

Best Regards, Christian
Cancel
Vote Up +3 Vote Down

Sign in to reply

Verify Answer

Cancel
0 hawkeyethehacker over 10 years ago in reply to doctorcdf

This update is greatly appreciated - thank you!

In regards to parts that need to be sourced from SparkFun etc, is there an estimated time of that being arranged? Sadly some of the project-critical parts are from suppliers other than Farnell.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 dougw over 10 years ago

I am wondering how many proposals were submitted for a big challenge like this....did anyone tally them up?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tomaja over 10 years ago

As far as I know, IAR Embedded Workbench for ARM is required if we want to try using the ADuCM350 SDK 2.2.0.0 and effectively ADuCM350.
Does anyone know if that's right, and if yes should I go for a trial download?
I just now saw Health and Impact Monitoring with Wearable Technology...

Thanks,
Dragan
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 clem57 over 10 years ago in reply to tomaja

Have you seen this for a download? http://www.analog.com/en/design-center/landing-pages/001/aducm350-design-resources.html
Clem
Cancel
Vote Up +1 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tomaja over 10 years ago in reply to clem57

Thanks for replying.
Yes, I've seen that and downloaded everything that's available but IAR Embedded Workbench wasn't included for me (but is required during SDK installation).
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tomaja over 10 years ago in reply to tomaja

Hi doctorcdf,
Can you direct us to someone from AnalogDevices for additional help regarding ADuCM350 SDK 2.2.0.0?

Thanks,
Dragan
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ravi_butani over 10 years ago

Hello All...
have any one tried to use electrolube resin for mold Main sensor???
I am eager to know the process of same...
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 doctorcdf over 10 years ago in reply to tomaja

I'll see who I can find to help; thanks.
Cancel
Vote Up +1 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tomaja over 10 years ago in reply to doctorcdf

Thanks!
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel