DIY Lithium Battery Charger Shield for Arduino » Electro-Labs.com
The Bill of Materials of the Lithium Battery Charger shield is given below.
| Quantity | Part Description | Designator |
|---|---|---|
| 1 | LT1510 Constant Current/Constant Voltage Battery Charger SO-16 | U1 |
| 1 | REF03 2.5V Voltage Reference SO8 | U2 |
| 1 | ACS712-5A Hall Effect Based Current Sensor 8-SOIC | U3 |
| 1 | LM258 Low Noise Operational Amplifier SO-8 | U4 |
| 1 | 5110 LCD Module | LCD1 |
| 2 | SS14 1A 40V Schottky Rectifier SMA | D1 D2 |
| 1 | 1N4148 General Purpose Diode SOD80C | D5 |
| 3 | BSS138 Mosfet SOT-23 | Q1 Q2 Q3 |
| 1 | Red LED 0805 | D3 |
| 1 | Green LED 0805 | D4 |
| 1 | 220nF 50V 0805 X7R SMD Ceramic Capacitor | C1 |
| 5 | 100nF 50V 0805 X7R SMD Ceramic Capacitor | C4 C8 C9 C10 C11 |
| 2 | 1nF 50V 0805 X7R SMD Ceramic Capacitor | C6 C7 |
| 1 | 10uF 25V 1206 X7R SMD Ceramic Capacitor | C3 |
| 1 | 1uF 25V 1206 X7R SMD Ceramic Capacitor | C5 |
| 1 | 22uF 16V Tantalum Capacitor B-Case | C2 |
| 1 | MSS1260-333 330uH Coilcraft Power Inductor | L1 |
| 3 | 100R 1% 0805 Resistor | R5 R6 R23 |
| 3 | 20K 1% 0805 Resistor | R7 R19 R22 |
| 2 | 1K 1% 0805 Resistor | R1 R10 |
| 1 | 70.6K 1% 0805 Resistor | R4 |
| 6 | 10K 1% 0805 Resistor | R11 R12 R13 R14 R20 R21 |
| 2 | 0805 Resistor Value Depends on the LEDs | R15 R16 |
| 1 | 3K8 1% 0805 Resistor | R24 |
| 3 | 100K 1% 0805 Resistor | R3 R17 R18 |
| 1 | 330R 1% 0805 Resistor | R9 |
| 1 | 300R 1% 0805 Resistor | R2 |
| 1 | 180K 1% 0805 Resistor | R8 |
| 4 | Tact Push Button SMD | SW1 SW2 SW3 SW4 |
| 1 | 1×6 2.54mm pitch 15mm height Male Header | J2 |
| 2 | 1×8 2.54mm pitch 15mm height Male Header | J3 J4 |
| 1 | 1×10 2.54mm pitch 15mm height Male Header | J1 |
| 1 | JST-PH Connector 2 Pin Right Angle | J5 |
| 1 | 1×2 5.2mm Pitch Screw Terminal Block | J6 |