Ultrazed vcu trd 2019.2 add SDI RX problem

Have you included this in the device tree?

--Dan

Hi Dan,

thanks for the help. What are you referring with "this"?

Thanks.

The SDI device.  I've not personally built the 2019.2 design at this time, but PetaLinux always needs devices to be defined.

For example, in SDSoC you have to add:

/{

xlnk {

compatible = "xlnx,xlnk-1.0";

};

};

into: project-spec/meta-user/recipes-bsp/devicetree/files/sytem-user.dtsi

You would need to do similar with the SDI device.

--Dan

Hi Dan,

yes I have inserted SDI device in device tree I think. This is my system-user.dtsi:

#include "system-conf.dtsi"

#include "uz7ev_evcc.dtsi"

#include "common.dtsi"

#include "apm.dtsi"

#include "xlnk.dtsi"

/ {

amba_pl: amba_pl@0 {

#address-cells = <2>;

#size-cells = <2>;

compatible = "simple-bus";

ranges ;

axi_gpio_0: gpio@a0000000 {

#gpio-cells = <3>;

clock-names = "s_axi_aclk";

clocks = <&zynqmp_clk 71>;

compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";

gpio-controller ;

reg = <0x0 0xa0000000 0x0 0x1000>;

xlnx,all-inputs = <0x1>;

xlnx,all-inputs-2 = <0x0>;

xlnx,all-outputs = <0x0>;

xlnx,all-outputs-2 = <0x0>;

xlnx,dout-default = <0x00000000>;

xlnx,dout-default-2 = <0x00000000>;

xlnx,gpio-width = <0x8>;

xlnx,gpio2-width = <0x20>;

xlnx,interrupt-present = <0x0>;

xlnx,is-dual = <0x0>;

xlnx,tri-default = <0xFFFFFFFF>;

xlnx,tri-default-2 = <0xFFFFFFFF>;

};

axi_gpio_1: gpio@a0001000 {

#gpio-cells = <3>;

clock-names = "s_axi_aclk";

clocks = <&zynqmp_clk 71>;

compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";

gpio-controller ;

reg = <0x0 0xa0001000 0x0 0x1000>;

xlnx,all-inputs = <0x0>;

xlnx,all-inputs-2 = <0x0>;

xlnx,all-outputs = <0x1>;

xlnx,all-outputs-2 = <0x0>;

xlnx,dout-default = <0x00000000>;

xlnx,dout-default-2 = <0x00000000>;

xlnx,gpio-width = <0x8>;

xlnx,gpio2-width = <0x20>;

xlnx,interrupt-present = <0x0>;

xlnx,is-dual = <0x0>;

xlnx,tri-default = <0xFFFFFFFF>;

xlnx,tri-default-2 = <0xFFFFFFFF>;

};

axi_gpio_2: gpio@a0002000 {

#gpio-cells = <3>;

clock-names = "s_axi_aclk";

clocks = <&zynqmp_clk 71>;

compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";

gpio-controller ;

reg = <0x0 0xa0002000 0x0 0x1000>;

xlnx,all-inputs = <0x1>;

xlnx,all-inputs-2 = <0x0>;

xlnx,all-outputs = <0x0>;

xlnx,all-outputs-2 = <0x0>;

xlnx,dout-default = <0x00000000>;

xlnx,dout-default-2 = <0x00000000>;

xlnx,gpio-width = <0x3>;

xlnx,gpio2-width = <0x20>;

xlnx,interrupt-present = <0x0>;

xlnx,is-dual = <0x0>;

xlnx,tri-default = <0xFFFFFFFF>;

xlnx,tri-default-2 = <0xFFFFFFFF>;

};

axi_gpio_3: gpio@a0062000 {

#gpio-cells = <3>;

clock-names = "s_axi_aclk";

clocks = <&zynqmp_clk 71>;

compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";

gpio-controller ;

reg = <0x0 0xa0062000 0x0 0x1000>;

xlnx,all-inputs = <0x0>;

xlnx,all-inputs-2 = <0x0>;

xlnx,all-outputs = <0x1>;

xlnx,all-outputs-2 = <0x0>;

xlnx,dout-default = <0x00000001>;

xlnx,dout-default-2 = <0x00000000>;

xlnx,gpio-width = <0x1>;

xlnx,gpio2-width = <0x20>;

xlnx,interrupt-present = <0x0>;

xlnx,is-dual = <0x0>;

xlnx,tri-default = <0xFFFFFFFF>;

xlnx,tri-default-2 = <0xFFFFFFFF>;

};

sdi_rx_input_v_frmbuf_wr: v_frmbuf_wr@a0070000 {

#dma-cells = <1>;

clock-names = "ap_clk";

clocks = <&misc_clk_0>;

compatible = "xlnx,v-frmbuf-wr-2.1", "xlnx,axi-frmbuf-wr-v2.1";

interrupt-names = "interrupt";

interrupt-parent = <&gic>;

interrupts = <0 92 4>;

reg = <0x0 0xa0070000 0x0 0x10000>;

xlnx,dma-addr-width = <32>;

xlnx,dma-align = <16>;

xlnx,fid ;

xlnx,max-height = <2160>;

xlnx,max-width = <3840>;

xlnx,pixels-per-clock = <2>;

xlnx,s-axi-ctrl-addr-width = <0x7>;

xlnx,s-axi-ctrl-data-width = <0x20>;

xlnx,vid-formats = "rgb888", "bgr888", "xbgr8888", "xrgb8888", "xbgr2101010", "uyvy", "y8", "y10", "vuy888", "xvuy8888", "yuvx2101010", "yuyv", "nv12", "nv16", "xv20", "xv15";

xlnx,video-width = <10>;

};

misc_clk_0: misc_clk_0 {

#clock-cells = <0>;

clock-frequency = <300681818>;

compatible = "fixed-clock";

};

sdi_rx_input_v_proc_ss_0: v_proc_ss@a0080000 {

clock-names = "aclk_axis", "aclk_ctrl";

clocks = <&misc_clk_0>, <&zynqmp_clk 71>;

compatible = "xlnx,v-proc-ss-2.2", "xlnx,v-vpss-scaler-1.0", "xlnx,vpss-scaler";

reg = <0x0 0xa0080000 0x0 0x40000>;

xlnx,colorspace-support = <0>;

xlnx,csc-enable-window = "true";

xlnx,enable-csc = "true";

xlnx,h-scaler-phases = <64>;

xlnx,h-scaler-taps = <8>;

xlnx,max-height = <2160>;

xlnx,max-num-phases = <64>;

xlnx,max-width = <3840>;

xlnx,num-hori-taps = <8>;

xlnx,num-vert-taps = <8>;

xlnx,pix-per-clk = <2>;

xlnx,samples-per-clk = <2>;

xlnx,scaler-algorithm = <2>;

xlnx,topology = <0>;

xlnx,use-uram = <0>;

xlnx,v-scaler-phases = <64>;

xlnx,v-scaler-taps = <8>;

xlnx,video-width = <10>;

scaler_ports: ports {

#address-cells = <1>;

#size-cells = <0>;

scaler_port0: port@0 {

/* For xlnx,video-format user needs to fill as per their requirement */

reg = <0>;

xlnx,video-format = <3>;

xlnx,video-width = <10>;

scaler_in: endpoint {

remote-endpoint = <&sdi_rx_out>;

};

};

scaler_port1: port@1 {

/* For xlnx,video-format user needs to fill as per their requirement */

reg = <1>;

xlnx,video-format = <3>;

xlnx,video-width = <10>;

scaler_out: endpoint {

remote-endpoint = <&vcap_csi_in>;

};

};

};

};

sdi_rx_input_v_smpte_uhdsdi_rx_ss: v_smpte_uhdsdi_rx_ss@a0030000 {

clock-names = "sdi_rx_clk", "video_out_clk", "s_axi_aclk";

clocks = <&misc_clk_1>, <&misc_clk_0>, <&zynqmp_clk 71>;

compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0", "xlnx,v-smpte-uhdsdi-rx-ss";

interrupt-names = "sdi_rx_irq";

interrupt-parent = <&gic>;

interrupts = <0 89 4>;

reg = <0x0 0xa0030000 0x0 0x10000>;

xlnx,exdes-board = "ZCU106";

xlnx,exdes-config = "Pass-Through";

xlnx,include-adv-features = "true";

xlnx,include-axilite = "true";

xlnx,include-edh = "true";

xlnx,line-rate = "12G_SDI_8DS";

xlnx,pixels-per-clock = <0x2>;

xlnx,video-intf = "AXI4_Stream";

sdirx_ports: ports {

#address-cells = <1>;

#size-cells = <0>;

sdirx_port: port@0 {

/* Fill the fields xlnx,video-format and xlnx,video-width based on user requirement */

reg = <0>;

xlnx,video-format = <0>;

xlnx,video-width = <10>;

sdi_rx_out: endpoint {

remote-endpoint = <&scaler_in>;

};

};

};

};

misc_clk_1: misc_clk_1 {

#clock-cells = <0>;

clock-frequency = <148500000>;

compatible = "fixed-clock";

};

vcu_0: vcu@a0100000 {

#address-cells = <2>;

#clock-cells = <1>;

#size-cells = <2>;

clock-names = "pll_ref", "aclk", "vcu_core_enc", "vcu_core_dec", "vcu_mcu_enc", "vcu_mcu_dec";

clocks = <&misc_clk_2>, <&zynqmp_clk 71>, <&vcu_0 1>, <&vcu_0 2>, <&vcu_0 3>, <&vcu_0 4>;

compatible = "xlnx,vcu-1.2", "xlnx,vcu";

interrupt-names = "vcu_host_interrupt";

interrupt-parent = <&gic>;

interrupts = <0 96 4>;

ranges ;

reg = <0x0 0xa0140000 0x0 0x1000>, <0x0 0xa0141000 0x0 0x1000>;

reg-names = "vcu_slcr", "logicore";

reset-gpios = <&gpio 119 0>;

encoder: al5e@a0100000 {

compatible = "al,al5e-1.2", "al,al5e";

interrupt-parent = <&gic>;

interrupts = <0 96 4>;

reg = <0x0 0xa0100000 0x0 0x10000>;

};

decoder: al5d@a0120000 {

compatible = "al,al5d-1.2", "al,al5d";

interrupt-parent = <&gic>;

interrupts = <0 96 4>;

reg = <0x0 0xa0120000 0x0 0x10000>;

};

};

misc_clk_2: misc_clk_2 {

#clock-cells = <0>;

clock-frequency = <33316544>;

compatible = "fixed-clock";

};

vcap_sdi {

compatible = "xlnx,video";

dma-names = "port0";

dmas = <&sdi_rx_input_v_frmbuf_wr 0>;

vcap_ports: ports {

#address-cells = <1>;

#size-cells = <0>;

vcap_port: port@0 {

direction = "input";

reg = <0>;

vcap_csi_in: endpoint {

remote-endpoint = <&scaler_out>;

};

};

};

};

};

};

HI there,

Next time, try using "Quote" or "Syntax Highlighting".  That will make this more clear to read.

Second, have you compared that to the files that come as part of the example?

--Dan

Hi Dan,

sorry. Next time I'll follow your advices. Is there a way to attach a file to an answer?

The system-user.dtsi is the same of the example (the included files)  but in addition I added in the queue the content of pl.dtsi file generated using petalinux-build -c device-tree -x configure.

Thank you.

Hi Pierluigi Michetti,

Your sdi vcu project run work fine ?

Can you share your project folder ? I can not run it. I think my problem is .dtsi files

Thanks,

Hi Pierluigi Michetti,

Your sdi vcu project run work fine ?

Can you share your project folder ? I can not run it. I think my problem is .dtsi files

Thanks,