.4mm to 2.54mm Routing

On 9/16/2016 5:33 AM, Tilmann Reh wrote:

warrenbrayshaw schrieb:

 

On 16/09/2016 5:14 p.m., Glenn Jones wrote:

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

Even if you get a trace between the QFN pins you will be up for the

expense of 2mil trace and space. The nature of your design would appear

not to justify that.

 

I didn't download the zip, however from his text I assume he just wants

a track from the QFN to the header, not traces between two QFN pads at

0.4 mm pitch.

 

Tilmann

 

Correct.

Glenn

On 9/16/2016 5:33 AM, Tilmann Reh wrote:

warrenbrayshaw schrieb:

 

On 16/09/2016 5:14 p.m., Glenn Jones wrote:

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

Even if you get a trace between the QFN pins you will be up for the

expense of 2mil trace and space. The nature of your design would appear

not to justify that.

 

I didn't download the zip, however from his text I assume he just wants

a track from the QFN to the header, not traces between two QFN pads at

0.4 mm pitch.

 

Tilmann

 

Correct.

Glenn

On 9/16/2016 2:10 AM, Tilmann Reh wrote:

Glenn Jones schrieb:

 

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

https://dl.dropboxusercontent.com/u/2238318/esp32hb.zip

 

Any suggestions?

 

Manual routing is the key to all autorouter problems.

Seriously.

 

Tilmann

 

I was afraid you were going to say that

Glenn

On 9/16/2016 2:10 AM, Tilmann Reh wrote:

Glenn Jones schrieb:

 

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

https://dl.dropboxusercontent.com/u/2238318/esp32hb.zip

 

Any suggestions?

 

Manual routing is the key to all autorouter problems.

Seriously.

 

Tilmann

 

I was afraid you were going to say that

Glenn

warrenbrayshaw schrieb:

On 16/09/2016 5:14 p.m., Glenn Jones wrote:

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

Even if you get a trace between the QFN pins you will be up for the

expense of 2mil trace and space. The nature of your design would appear

not to justify that.

I didn't download the zip, however from his text I assume he just wants

a track from the QFN to the header, not traces between two QFN pads at

0.4 mm pitch.

Tilmann

On 16/09/2016 5:14 p.m., Glenn Jones wrote:

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

https://dl.dropboxusercontent.com/u/2238318/esp32hb.zip

 

Any suggestions?

 

Glenn

Even if you get a trace between the QFN pins you will be up for the

expense of 2mil trace and space. The nature of your design would appear

not to justify that.

Warren

Glenn Jones schrieb:

I seem to be having a heck of a time getting the autorouter to route

between .4mm pitch 48 pin qfn smd and 2 x 2.54mm pth header strips.

 

https://dl.dropboxusercontent.com/u/2238318/esp32hb.zip

 

Any suggestions?

Manual routing is the key to all autorouter problems.

Seriously.

Tilmann