Actions
Forum Thread Details
  • State Not Answered
  • Replies 7 replies
  • Subscribers 302 subscribers
  • Views 1026 views
  • Users 0 members are here
Related
See a helpful answer?

Be sure to click 'more' and select 'suggest as answer'!

If you're the thread creator, be sure to click 'more' then 'Verify as Answer'!

Need Help Identifying and Finding a Specific Componet

Former Member

I have a bad LED 3 digit display and i have not been able to find one with the proper terminals to replace it with. The issue is all the ones i have found dont have the gap on the five pin side. Here is the info I have.

 

Over all display: 13.5mm X 22mm X 6mm (tall)

Digits: 7mm X 4mm

Pins: .5mm

Pin spacing (from pin center to pin center): 2.5mm

Display color: Red

 

On the side it says:

A303E-CL G/W

S0826 04 RoHS P

 

The display and digit size can fluctuate a little but the pins need to be the same as its for a pre-manufactured board.

 

If it maters its out of an Autometer Pro-Comp Ultra-Lite wideband air/fuel gauge.

Attachments:
image
image
Parents
  • 0

    I found your direct replacement if you ever need one again.  Here is a little more information to help.

     

    Your P/N was:

    A303E-CL G/W

    A signifies Common Anode. 

    E designates color as Red High Efficiency.

    G = Green, Y = Yellow, R = Super Red

    Therefore the P/N equivalents would be A303X with X being any letter.  Looking at the specifications, the current and voltage differences are insignificant from a circuit functionality perspective for what we need these for.

     

    The readout is a 3 digit, 24 LED.

    Mfg: American Opto Plus

    Pinout indicates no connection for pin 10.

    Pin 1 starts Lower Left looking from top view of readout through the device

     

    The direct replacement parts can be ordered through:

    DComponents

    www.DComponents.com

     

    The readout cost was $3.36 each for the exact replacement and $3.31 for other colors.

    Leadtime is about 4-6 weeks if they do not have it in stock. 

    They had green in stock so I bought 3 and back ordered the exact parts.

     

    Hope this helps someone else in the future.

    My Application was for an AutoMeter A/F (Air Fuel) Ratio Gauge.  I had two of these gauges with defective readouts lasting only about a year each.  Expensive gauge at $400 each for the display to only last about a year.  It could be heat related since these gauges are often mounted in gauge pod housing on a dash or the A Pillar in a car.

Reply
  • 0

    I found your direct replacement if you ever need one again.  Here is a little more information to help.

     

    Your P/N was:

    A303E-CL G/W

    A signifies Common Anode. 

    E designates color as Red High Efficiency.

    G = Green, Y = Yellow, R = Super Red

    Therefore the P/N equivalents would be A303X with X being any letter.  Looking at the specifications, the current and voltage differences are insignificant from a circuit functionality perspective for what we need these for.

     

    The readout is a 3 digit, 24 LED.

    Mfg: American Opto Plus

    Pinout indicates no connection for pin 10.

    Pin 1 starts Lower Left looking from top view of readout through the device

     

    The direct replacement parts can be ordered through:

    DComponents

    www.DComponents.com

     

    The readout cost was $3.36 each for the exact replacement and $3.31 for other colors.

    Leadtime is about 4-6 weeks if they do not have it in stock. 

    They had green in stock so I bought 3 and back ordered the exact parts.

     

    Hope this helps someone else in the future.

    My Application was for an AutoMeter A/F (Air Fuel) Ratio Gauge.  I had two of these gauges with defective readouts lasting only about a year each.  Expensive gauge at $400 each for the display to only last about a year.  It could be heat related since these gauges are often mounted in gauge pod housing on a dash or the A Pillar in a car.

Children
No Data