Booting cisco ios on Raspberry pi

Question

i was thinking about booting up cisco ios on raspberry pi. help me regarding that. is it possible to do so?

Former Member · Answer

Before we enable logging you should verify that your Pi has its clock configured correctly. ser2net will add a timestamp to its log files and logging is pretty much useless if you don’t have the correct date or time. By default it will synchronize its time by using NTP but the timezone might be incorrect. Changing the timezone is easy to do: $ sudo cp /usr/share/zoneinfo/Europe/Amsterdam /etc/localtime This will change the timezone to CEST (Central European Time) for me . Let’s verify it: $ date Fri Jul 19 11:55:27 CEST 2013 That’s looking good to me. Now we’ll create a folder that will hold our log files. I will save everything in the /var/log/ser2net folder: $ sudo mkdir /var/log/ser2net Now you need to edit the /etc/ser2net.conf file again and add the following: TRACEFILE:tr1:/var/log/ser2net/tr-p-Y-M-D-H:i:s.U 4001:telnet:0:/dev/ttyUSB0:9600 8DATABITS NONE 1STOPBIT banner tr=tr1 timestamp The ‘TRACEFILE’ line is new and at the end of the 4001:telnet… line we will add “tr=tr1 timestamp”. This will enable logging for this port and add timestamps to the log files. You will have to restart ser2net before logging is active. The next time you connect you will see the log files in the /var/log/ser2net folder: $ ls /var/log/ser2net tr-4001-2013-Jul-19-09:18:26.893894 You now have a console server that saves logging information. In the next part I’ll show you how to enable wireless support and how to secure your Pi: Wireless Access Point Most wireless adapters also support access point mode. This is very useful since we can make our Pi broadcast a SSID and let wireless clients connect to it. This turns our Pi into a wireless console server…nice! Plug in your wireless USB adapter and see if it’s recognized: $ lsusb Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. Bus 001 Device 004: ID 0bda:8179 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC Keep in mind that the USB port of the Raspberry Pi has limited power and not all wireless adapters are supported. Take a look at the elinux Rpi page to see which adapters are supported. If your USB device is recognized we still have to check if our wireless drivers are operational: $ iwconfig wlan0 unassociated Nickname:"&lt;WIFI@REALTEK&gt;" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Sensitivity:0/0 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 If iwconfig doesn’t give you any information you probably have an issue with drivers. Once your wireless card is up and running we will install hostapd. This configures the wireless adapter as an access point: $ sudo apt-get install hostapd We’ll configure the wireless adapter to use a static IP address instead of DHCP: $ sudo vi /etc/network/interfaces Remove the following two lines from this file: iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf And replace them with the following lines: iface wlan0 inet static address 172.16.82.254 netmask 255.255.255.0 Our wlan0 interface will use static IP address 172.16.82.254 /24. Now we’ll configure hostapd to set some parameters for the access point: $ sudo vi /etc/hostapd/hostapd.conf ssid=Console wpa_passphrase=mysecurepassphrase wpa=3 You can leave most of the settings in this file alone but I will change the SSID and the WPA passphrase. The passphrase will be “mysecurepassphrase” and wpa=3 means we will support WPA and WPA2. Let’s start hostapd: $ sudo service hostapd start To make sure hostapd runs after rebooting the Pi we’ll add it to the startup list: $ sudo update-rc.d hostapd enable Your Raspberry Pi should now be broadcasting SSID “Console” but wireless clients will have to configure a static IP address. We’ll fix this by installing a DHCP server: $ sudo apt-get install dnsmasq At the bottom of this file you should add the following two lines: interface=wlan0 dhcp-range=172.16.82.10,172.16.82.100,12h This ensures that the DHCP server only runs for wireless clients and that we’ll use 172.16.82.10 – 172.16.82.100 for DHCP clients. Restart the DHCP server: $ sudo service dnsmasq restart [ ok ] Restarting DNS forwarder and DHCP server: dnsmasq. And make sure it boots at startup: $ sudo update-rc.d dnsmasq enable Your Raspberry Pi is now configured as an access point. Wireless clients are now able to connect to it and access the console port by telnetting to 172.16.82.254:4001. In the final part of this tutorial we’ll take a look at some security measures. Your Pi is using a default username / password and the firewall is allowing all traffic. Security Even though the Pi is a little box, it’s still a fully functional Linux server. It’s best to take some security measures to protect it. I’m going to change the default username, tighten SSH security a bit and add some rules to the IPTables firewall. Change username First i’ll replace the default user ‘pi’ with my own username: $ sudo adduser renemolenaar Adding user `renemolenaar' ... Adding new group `renemolenaar' (1002) ... Adding new user `renemolenaar' (1001) with group `renemolenaar' ... Creating home directory `/home/renemolenaar' ... Copying files from `/etc/skel' ... Don’t forget to add a password: $ sudo passwd renemolenaar Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully And we need to add the new user to the sudoers list or you can’t run any important commands: $ sudo vi /etc/sudoers Change the following line: pi ALL=(ALL) NOPASSWD: ALL to: renemolenaar ALL=(ALL) NOPASSWD: ALL Now try if you are able to log into the Pi using your new username and if you can use sudo. When it’s working we’ll delete the old ‘pi’ account: $ sudo deluser pi Removing user `pi' ... Warning: group `pi' has no more members. Done. I always like to change the default SSH port and ensure that the root user can’t login through SSH directly: $ sudo vi /etc/ssh/sshd_config Now change the following line: PermitRootLogin yes To: PermitRootLogin no And change the port number to something else: Port 22 To: Port 10050 Don’t forget to restart SSH to apply the changes you made: $ sudo service ssh restart This makes SSH a little bit more secure. IPTables Firewall Your Raspberry Pi has the IPtables firewall installed on it by default but we’ll have to add some rules ourselves. I want to make sure outside LAN users can only connect to TCP 4001 for the console port and TCP port 10050 to access SSH. The same rules will apply to wireless users with the exception that they also will request an IP address through DHCP. Create a new file for IPTables: $ sudo vi /etc/iptables-rules And add the following lines to it: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -i lo -j ACCEPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT # LAN Rules -A INPUT -i eth0 -p tcp -m tcp --dport 4001 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 10050 -j ACCEPT # WIRELESS Rules -A INPUT -i wlan0 -p udp -m udp --dport 67 -j ACCEPT -A INPUT -i wlan0 -p tcp -m tcp --dport 4001 -j ACCEPT -A INPUT -i wlan0 -p tcp -m tcp --dport 10050 -j ACCEPT # Allow ICMP packets necessary for MTU path discovery -A INPUT -p icmp --icmp-type fragmentation-needed -j ACCEPT # Allow echo request -A INPUT -p icmp --icmp-type 8 -j ACCEPT -A INPUT -j DROP COMMIT Save your file and load the firewall rules: $ sudo iptables-restore < /etc/iptables-rules Let’s make sure these rules are loaded when the Pi reboots: $ sudo vi /etc/network/interfaces Add the following line at the bottom of the interfaces file: pre-up /sbin/iptables-restore < /etc/iptables-rules This is a good moment to reboot your Pi and verify that iptables is running: $ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:4001 ACCEPT tcp -- anywhere anywhere tcp dpt:10050 ACCEPT tcp -- anywhere anywhere tcp dpt:4001 ACCEPT tcp -- anywhere anywhere tcp dpt:10050 ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT icmp -- anywhere anywhere icmp fragmentation-needed ACCEPT icmp -- anywhere anywhere icmp echo-request DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Your Raspberry Pi is now protected by IPTables.