element14's The Ben Heck Show

Forum 3D Printers! (continued)

Join element14's The Ben Heck Show to participate - click to join for free!

Actions

Forum Thread Details

State Not Answered
Replies 5 replies
Subscribers 30 subscribers
Views 490 views
Users 0 members are here

Related

3D Printers! (continued)

tim12 over 13 years ago

Hi to all, thanks nate (who replied to my previous message)

I would be very grateful if you answer my questions:

After my previous questions on this website:

http://www.element14.com/community/thread/22236

I am now deciding to buy this Hot end:

http://www.ebay.co.uk/itm/HotEnd-Fully-Assembled-and-Wired-FREE-Hobbed-Bolt-RepRap-3D-Printer-Hot-End-/281065376032?pt=LH_DefaultDomain_3&var=&hash=item4170cd4920

Is it trust worthy? What is the best size for the ptfe insulator? I have also found out that for the arduino I am choosing this one:

http://www.ebay.co.uk/itm/ATmega2560-16AU-Board-USB-Cable-ARDUINOs-IDE-MEGA-2560-/170975431415?pt=Wissenschaftliche_Ger%C3%A4te&hash=item27ceee0af7

Is it compatible with the hot end? And what do they mean by bootloaded... (on the website)? I have also found the

A4988 Stepper Motor Driver Carrier

which is on this website:

http://www.pololu.com/catalog/product/1182

I have also found the ramps 1.4, fully assembled here:

http://reprapworld.com/?products_details&products_id=50&cPath=1591_1593

Thanks again

Tim

Parents

0 Nate1616 over 13 years ago

Hey Tim
Since i dont know much about that hotend the only comment i will make is, it is compatible with the ramps but you will have to cut off the connecter since it was set up for the Sanguinololu. Here is the 2 different wire schematics http://reprap.org/mediawiki/images/6/6d/Rampswire14.svg http://reprap.org/mediawiki/images/2/2a/Sanguinololu12.svg. I personally use the Lulzbot Budaschnozzle and have had very good luck with it http://www.lulzbot.com/?q=Budaschnozzle-1.2-w-0.35mm-Nozzle. It might be in your interest to get the rest of the supplies from the same place to cut back on shipping. here is a complete set from reprapword http://reprapworld.com/?products_details&products_id=153&cPath=1645. This has everything you would need Arduino, ramps and stepsticks(stepper drivers).
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tim12 over 13 years ago in reply to Nate1616

What about this hot end:

http://www.ebay.co.uk/itm/HotEnd-Hot-End-EZ-for-RepRap-3D-printers-/110985799252?pt=LH_DefaultDomain_0&hash=item19d744e654

Thanks LOADS!!
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Nate1616 over 13 years ago in reply to tim12

That hotend will work with your setup but again since I've never used it i couldnt tell you its performance.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 Nate1616 over 13 years ago in reply to tim12

That hotend will work with your setup but again since I've never used it i couldnt tell you its performance.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

No Data