Actions
Forum Thread Details
  • Replies 4 replies
  • Subscribers 188 subscribers
  • Views 327 views
  • Users 0 members are here
Related

Electrical contacts in Pa ckages?

mprowe@peritonlane.net

Hi,

 

I wish to make an electrical connection (such that a polygon on the board

will connect to it) within a device.

Can I attach a pin to anything other than a Pad or SMD?

 

Ideally, I'd like to define a wide wire, polygon or rectangle on the top &

bottom layer to provide a thermal AND electrical contact for the physical

device.

 

Regards, Martin

--

Web access to CadSoft support forums at www.eaglecentral.ca.  Where the CadSoft EAGLE community meets.

 

  • in reply to autodeskguest

    Thank you Warren,

     

    That's what I needed to find. First para says:

     

    As soon as the center of the pad or SMD is inside the polygon's area or a

    wire begins at the

    center of a pad, it is recognized as a part of the PAD/SMD.

     

    My line did not start at the centre of a pad. Silly me....

     

    Regards, Martin

    --

    Web access to CadSoft support forums at www.eaglecentral.ca.  Where the CadSoft EAGLE community meets.

     

  • in reply to mprowe@peritonlane.net

    On 11/05/2016 3:30 a.m., Martin Rowe wrote:

    CadSoft Support wrote on Tue, 10 May 2016 14:13

    Am 10.05.2016 um 12:52 schrieb Martin Rowe:

    If the center of the SMD/PAD is indide the wire/

    polygon it will be recognized as part of the signal.

     

    Thank you for your advice, Richard.

    From the following images can you see what I am doing wrong?

    The images at the top are cut from the Package Editor with the Board

    results below.

     

     

    Regards, Martin

    PS - Just to avoid going off at a tangent, I am trying to get an

    edge-plated slot.

    I have seen the example board on OSH-Park, but that only seems to work if

    you place the slot on the board.

    I would like the slot defined in the Package.

     

     

    Hi Martin

     

    Have a read of the manual

    Chapter 8.14 Arbitrary Pad Shapes

     

    HTH

    Warren

     

  • in reply to autodeskguest

    CadSoft Support wrote on Tue, 10 May 2016 14:13

    Am 10.05.2016 um 12:52 schrieb Martin Rowe:

    If the center of the SMD/PAD is indide the wire/

    polygon it will be recognized as part of the signal.

     

     

    Thank you for your advice, Richard.

    From the following images can you see what I am doing wrong?

    The images at the top are cut from the Package Editor with the Board

    results below.

     

     

    Regards, Martin

    PS - Just to avoid going off at a tangent, I am trying to get an

    edge-plated slot.

    I have seen the example board on OSH-Park, but that only seems to work if

    you place the slot on the board.

    I would like the slot defined in the Package.

     

    --

    Web access to CadSoft support forums at www.eaglecentral.ca.  Where the CadSoft EAGLE community meets.

     

  • Am 10.05.2016 um 12:52 schrieb Martin Rowe:

    Hi,

     

    I wish to make an electrical connection (such that a polygon on the board

    will connect to it) within a device.

    Can I attach a pin to anything other than a Pad or SMD?

     

    Ideally, I'd like to define a wide wire, polygon or rectangle on the top &

    bottom layer to provide a thermal AND electrical contact for the physical

    device.

     

    Regards, Martin

     

     

    You have to use a SMD or a PAD. But you can cover the PAD/SMD with

    a polygon or wire. If the center of the SMD/PAD is indide the wire/

    polygon it will be recognized as part of the signal.

    Think of solder stop mask and solder paste mask as well then.....

     

    --

    Mit freundlichen Gruessen / Best regards

    Richard Hammerl

      CadSoft Support -- hotline@cadsoft.de

      FAQ: http://www.cadsoft.de/training/faq/