Actions
Forum Thread Details
  • Replies 6 replies
  • Subscribers 359 subscribers
  • Views 980 views
  • Users 0 members are here
Related

Extreme ESD in the workplace

Catwell
Here is an accident waiting to happen. I shock myself every time I touch anything grounded in the engineering department. Even if I take a single step, touch anything metal, I get shocked. Once, I let the charge build for a while, and then I ground out, and I still feel the effects days later. If that is happening to me, you can imagine what that could be doing to circuits I put together.

The company's best effort to curb the issue is offering anti-static spray liquid to cover everything. Not the most effective, I trade marginally less shock of a greater degree of moisture on everything. I find this to be an insane alternative. So, I've stuck to being excessively cautions with my circuits. However, I will admit, I've shocked my circuits a few times.

This is a major issue, and I have had this same one at many jobs I have held. I'm sure I'm not the only having this problem. Unfortunately, my job's building was built 50 years ago and grounded, copper laced, carpet wasn't an option during the install. Is there anything I could do to fix this, at least for myself? One requirement,  I need to be mobile. I go from my desk to the lab often, and I usually carry my circuits with me.
 
Cabe
Parents

  • Hi Cabe,

     

    Why not use a grounding wrist-strap(Like the ones computer techs use) along with an anti static floor mat? This is the recommendation I've always seen. The floor mat isn't very mobile, but the wrist strap is and it offers a decent amount of protection. If you have the ARRL Handbook, one of the last sections in the book talks about setting up a shop and how to properly ground yourself and equipment to avoid these types of shocks.

     

    hth,

    Jorge Garcia

  • in reply to Jorge_Garcia

    Jorge,

     

    That is the tried-and-true method. Unfortunately, the company doesn't want to buy anything for me to set up my various areas properly.

     

    What I would like to do is wear some sort of spikes, cleats, to constantly "ground" myself. I doubt it would be effective though.

     

    Otherwise I would need to approach Telsa level wireless energy transfer. A personal "lightening-rod."

     

    Cabe

  • in reply to Catwell

    I had a problem with ESD in a Computer room I worked in a few years ago.

    I could get 5mm sparks after walking across the room.

     

    In the short term I solved the problem by removing my shoes.

    Apparently slightly damp socks have a lower dialectric constant than polyurethane. :-)

     

    It will be the very high resistance of your shoe-soles and the charge transfer as you move your feet on the carpet that allow your body to charge up.

     

    If you stick a drawing pin into the heel of your shoe and  wire it to a bit of metal foil inside the shoe with a 1M resistor this should be enough to discharge you without increasing your risk of electrocution from 240V mains faults.

     

    This will also allow people to instantly recognise you as an engineer. :-)

     

    TRM

Reply
  • in reply to Catwell

    I had a problem with ESD in a Computer room I worked in a few years ago.

    I could get 5mm sparks after walking across the room.

     

    In the short term I solved the problem by removing my shoes.

    Apparently slightly damp socks have a lower dialectric constant than polyurethane. :-)

     

    It will be the very high resistance of your shoe-soles and the charge transfer as you move your feet on the carpet that allow your body to charge up.

     

    If you stick a drawing pin into the heel of your shoe and  wire it to a bit of metal foil inside the shoe with a 1M resistor this should be enough to discharge you without increasing your risk of electrocution from 240V mains faults.

     

    This will also allow people to instantly recognise you as an engineer. :-)

     

    TRM

Children
No Data