Actions
Forum Thread Details
  • Replies 12 replies
  • Subscribers 7 subscribers
  • Views 2769 views
  • Users 0 members are here
Related

Does anyone have experience with EnOcean STM 300

robertheinze

Hello!

 

I am planning to use a motion detector based on EnOcean technology. The available solar powered OEM products using the STM 300 are rather expensive (70€ and more), so I was wondering whether anyone has experience in building your own motion detector Based on STM 300 or if anyone has found a cheaper version of the product.

 

The idea is have it communicating with a EnOcean Pi modul on a RPi.

Thanks for help.

Regards

Robert

Parents

  • Hii ....

    You can refer my post Fireman Minion: STM330 Temp-Sensor with custom Analog and Digital Input (Part1) regarding STM300 also you will find compile codes to interface external analog and digital sensor with STM300...

    All the best....

  • in reply to ravi_butani

    HI Ravi,a

    Are you still in? unfortunately，i have some issues about programming of STM300,need some  circuit diagrams of this programming. in my project,it always failes in "PrgArea falied",and I don't know what it means.

    maybe you can give me a hint.

    thanks

    Lemon

  • in reply to kee

    Forget_me_not : My Smart Home Post#9 Week-8 (Part1) Sensors@enocean and Accuator@arduino+RFtransceiver

    Try code attached in above blog with keil... Keil c51 licensed version required for creating hex file... 8kb code size limited demo version of keil c51 will not work...

    If you still get error than let me know...

    Ravi

  • in reply to ravi_butani

    hello,this is my problem.

    The EOP-350 UPB always cann't communicate  with the TCM320U,and programming the module won’t be possible.It is received the error message below

     

     

    Init device 'EOZ5VUQ5A'........................................OK

    Programmer firmware version ' DA'..............................OK

    Connected to 'EO3000I' BootLoader 'v2.3.0.0'...................OK

    Read CfgArea to buffer.........................................OK

     

     

    ERROR: FracN RX/TX values missing, radio is not available!

     

     

    Please restore your config area:

    Use DolphinStudio -> Utilities -> Restore config area from backup

     

     

    Aborting programming!

     

     

    Reset chip.....................................................OK

    Disconnect.....................................................OK

     

     

    I tried to restore EO3000I configuration area from backup and using the Programmer section of DolphinStudio to update the TCM300 and received the error message below.

     

     

    EOP-EnOcean Programmer v2.3.4.0 (c) Copyright 2009 EnOcean GmbH

    -----------------------------------------------------------------

     

     

    Init device 'EOZ5VUQ5A'........................................OK

    Programmer firmware version ' DA'..............................OK

    Connected to 'EO3000I' BootLoader 'v2.3.0.0'...................OK

    Read CfgArea to buffer.........................................OK

    Read chip information..........................................OK

    Backup for ChipID: 0x19AB92D already exists....................OK

    Check ChipID...................................................OK

    Write PrgArea..............................................FAILED

    Reset chip.....................................................OK

    Disconnect.....................................................OK

     

     

    I really do not know what the problem is!

    maybe you can give me a hint.

    thanks

    Lemon KEY

Reply
  • in reply to ravi_butani

    hello,this is my problem.

    The EOP-350 UPB always cann't communicate  with the TCM320U,and programming the module won’t be possible.It is received the error message below

     

     

    Init device 'EOZ5VUQ5A'........................................OK

    Programmer firmware version ' DA'..............................OK

    Connected to 'EO3000I' BootLoader 'v2.3.0.0'...................OK

    Read CfgArea to buffer.........................................OK

     

     

    ERROR: FracN RX/TX values missing, radio is not available!

     

     

    Please restore your config area:

    Use DolphinStudio -> Utilities -> Restore config area from backup

     

     

    Aborting programming!

     

     

    Reset chip.....................................................OK

    Disconnect.....................................................OK

     

     

    I tried to restore EO3000I configuration area from backup and using the Programmer section of DolphinStudio to update the TCM300 and received the error message below.

     

     

    EOP-EnOcean Programmer v2.3.4.0 (c) Copyright 2009 EnOcean GmbH

    -----------------------------------------------------------------

     

     

    Init device 'EOZ5VUQ5A'........................................OK

    Programmer firmware version ' DA'..............................OK

    Connected to 'EO3000I' BootLoader 'v2.3.0.0'...................OK

    Read CfgArea to buffer.........................................OK

    Read chip information..........................................OK

    Backup for ChipID: 0x19AB92D already exists....................OK

    Check ChipID...................................................OK

    Write PrgArea..............................................FAILED

    Reset chip.....................................................OK

    Disconnect.....................................................OK

     

     

    I really do not know what the problem is!

    maybe you can give me a hint.

    thanks

    Lemon KEY

Children
No Data