Text not pointing correct

Harry H. Arends schrieb:

From a DXF i created a scriptfile to place text along a circle.

The text should be readble in the same way. It shows correct in the DXF

file

but on the board a section is displayed correct but the other part is a

sort

of mirrord.

Is this to be fixed becourse if i do the same by hand it shows at it should

be.

 

Harry

 

This is the code:

CHANGE SIZE 5.00;

TEXT R0 '1' (-60,680580 -1,897160);

TEXT R7.5 '2' (-60,395600 -9,873900);

TEXT R15 '3' (-58,576140 -17,679940);

TEXT R22.5 '4' (-55,753360 -25,181700);

TEXT R30 '5' (-51,980000 -32,253420);

TEXT R37.5 '6' (-47,381700 -38,823480);

TEXT R45 '7' (-41,828620 -44,616920);

TEXT R52.5 '8' (-35,633140 -49,702260);

TEXT R60 '9' (-28,826880 -53,935400);

TEXT R67.5 '10' (-22,352520 -59,238540);

TEXT R75 '11' (-14,244620 -61,020160);

TEXT R82.5 '12' (-6,209340 -62,860440);

TEXT R90 '13' (2,062680 -63,140440);

TEXT R97.5 '14' (10,300480 -62,338340);

TEXT R105 '15' (18,364440 -60,472820);

TEXT R112.5 '16' (26,148460 -57,647580);

TEXT R120 '17' (33,416360 -53,667460);

TEXT R127.5 '18' (40,149460 -48,853900);

TEXT R135 '19' (46,196660 -43,202700);

TEXT R142.5 '20' (51,580580 -36,907280);

TEXT R150 '21' (55,399960 -29,536740);

TEXT R157.5 '22' (59,257220 -22,251560);

TEXT R165 '23' (61,668640 -14,333880);

TEXT R172.5 '24' (63,025960 -6,169200);

TEXT R180 '25' (63,311100 2,102820);

TEXT R187.5 '26' (62,596800 10,352840);

TEXT R195 '27' (60,633380 18,403240);

TEXT R202.5 '28' (57,726500 26,152740);

TEXT R210 '29' (53,832980 33,456500);

TEXT R217.5 '30' (49,145520 40,286360);

TEXT R225 '31' (43,014660 45,883240);

TEXT R232.5 '32' (36,976040 51,494600);

TEXT R240 '33' (29,952280 55,873100);

TEXT R247.5 '34' (22,417080 59,297340);

TEXT R255 '35' (14,500740 61,713720);

TEXT R262.5 '36' (6,346940 63,159020);

TEXT R270 '37' (-1,937300 63,346080);

TEXT R277.5 '38' (-10,175100 62,543980);

TEXT R285 '39' (-18,237700 60,673500);

TEXT R292.5 '40' (-26,048020 57,913460);

TEXT R300 '41' (-33,040960 53,440080);

TEXT R307.5 '42' (-40,024040 49,059540);

TEXT R315 '43' (-46,071240 43,408360);

TEXT R322.5 '44' (-51,329040 37,016180);

TEXT R330 '45' (-55,711980 29,994980);

TEXT R337.5 '46' (-59,218380 22,493080);

TEXT R345 '47' (-61,543200 14,539540);

TEXT R352.5 '48' (-62,900520 6,374860);

 

I cannot follow you exactly, but why don't you use polar coordinates

like TEXTxxxxx(Pdistance angle);

where the distance and the angle is from the 0,0 position.

(Observe the "P" in front of distance for "polar").

If you want a different position as the center of your circle set this

with "Mark" and use "RP" for relative polar, like

TEXTxxxxx(RPdistance angle);

text r45 '45' (RP400 45) would read as:

Rotate text '45' by 45° at a distance of 400 Grid-units and an angle of

45° from a position set with "Mark".

--

Gruß / regards

Jörn

Harry H. Arends schrieb:

From a DXF i created a scriptfile to place text along a circle.

The text should be readble in the same way. It shows correct in the DXF

file

but on the board a section is displayed correct but the other part is a

sort

of mirrord.

Is this to be fixed becourse if i do the same by hand it shows at it should

be.

 

Harry

 

This is the code:

CHANGE SIZE 5.00;

TEXT R0 '1' (-60,680580 -1,897160);

TEXT R7.5 '2' (-60,395600 -9,873900);

TEXT R15 '3' (-58,576140 -17,679940);

TEXT R22.5 '4' (-55,753360 -25,181700);

TEXT R30 '5' (-51,980000 -32,253420);

TEXT R37.5 '6' (-47,381700 -38,823480);

TEXT R45 '7' (-41,828620 -44,616920);

TEXT R52.5 '8' (-35,633140 -49,702260);

TEXT R60 '9' (-28,826880 -53,935400);

TEXT R67.5 '10' (-22,352520 -59,238540);

TEXT R75 '11' (-14,244620 -61,020160);

TEXT R82.5 '12' (-6,209340 -62,860440);

TEXT R90 '13' (2,062680 -63,140440);

TEXT R97.5 '14' (10,300480 -62,338340);

TEXT R105 '15' (18,364440 -60,472820);

TEXT R112.5 '16' (26,148460 -57,647580);

TEXT R120 '17' (33,416360 -53,667460);

TEXT R127.5 '18' (40,149460 -48,853900);

TEXT R135 '19' (46,196660 -43,202700);

TEXT R142.5 '20' (51,580580 -36,907280);

TEXT R150 '21' (55,399960 -29,536740);

TEXT R157.5 '22' (59,257220 -22,251560);

TEXT R165 '23' (61,668640 -14,333880);

TEXT R172.5 '24' (63,025960 -6,169200);

TEXT R180 '25' (63,311100 2,102820);

TEXT R187.5 '26' (62,596800 10,352840);

TEXT R195 '27' (60,633380 18,403240);

TEXT R202.5 '28' (57,726500 26,152740);

TEXT R210 '29' (53,832980 33,456500);

TEXT R217.5 '30' (49,145520 40,286360);

TEXT R225 '31' (43,014660 45,883240);

TEXT R232.5 '32' (36,976040 51,494600);

TEXT R240 '33' (29,952280 55,873100);

TEXT R247.5 '34' (22,417080 59,297340);

TEXT R255 '35' (14,500740 61,713720);

TEXT R262.5 '36' (6,346940 63,159020);

TEXT R270 '37' (-1,937300 63,346080);

TEXT R277.5 '38' (-10,175100 62,543980);

TEXT R285 '39' (-18,237700 60,673500);

TEXT R292.5 '40' (-26,048020 57,913460);

TEXT R300 '41' (-33,040960 53,440080);

TEXT R307.5 '42' (-40,024040 49,059540);

TEXT R315 '43' (-46,071240 43,408360);

TEXT R322.5 '44' (-51,329040 37,016180);

TEXT R330 '45' (-55,711980 29,994980);

TEXT R337.5 '46' (-59,218380 22,493080);

TEXT R345 '47' (-61,543200 14,539540);

TEXT R352.5 '48' (-62,900520 6,374860);

 

I cannot follow you exactly, but why don't you use polar coordinates

like TEXTxxxxx(Pdistance angle);

where the distance and the angle is from the 0,0 position.

(Observe the "P" in front of distance for "polar").

If you want a different position as the center of your circle set this

with "Mark" and use "RP" for relative polar, like

TEXTxxxxx(RPdistance angle);

text r45 '45' (RP400 45) would read as:

Rotate text '45' by 45° at a distance of 400 Grid-units and an angle of

45° from a position set with "Mark".

--

Gruß / regards

Jörn