Consistency errors

I have 5 consistency errors, on sections of my board that I wired several days ago. One of the errors is on an airwire. Do I have to delete the entire net to find the offending trace. I also have missing airwires; parts with no airwires attached at one end. I also have airwires still in place after I have placed traces, that ratsnest won't clear. I assume that the consistency errors are preventing annotation between the schematic and the board. Can you help?

Parents

0 rachaelp over 9 years ago

Hi Jim,

Did you edit the schematic or board without the corresponding file open?
This is a guaranteed way to create consistency errors. The missing air
wires would probably be because the net was added in the schematic while
back annotation wasn't working so the board knows nothing about the net.

You've not really given enough information about what the errors actually
are for us to be able to help, can you post up what the actual messages are
saying?

Basically what you'll need to do is back out any additions to the schematic
that happened while not in sync and make sure any property changes are in
sync across both the schematic and the board. Keep running ERC and working
through the list of differences until you see all the errors are cleared.
If you can supply more info then we can probably help more.

Best Regards,

Rachael
--
Web access to CadSoft support forums at www.eaglecentral.ca. Where the CadSoft EAGLE community meets.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 maciv4 over 9 years ago in reply to rachaelp

I now have the following errors:
Different connections on R48 pin 2 and pad 2 (-12V/$$1)   2
Different connections on R84 pin 2 and pad 2 (-12V/$$1)   3
Different connections on U15P pin V- and pad 4 (-12V/$$1)    2
Different connections on U17P pin V- and pad 4 (-12V/$$1)    3
Different connections on U20P pin V- and pad 4 (-12V/$$1)    3
Part R46 has different values in schematic and board (2.61k Ohms/2.61K)
Part R48 has different values in schematic and board (2.2k Ohms/2.2K)
Part R84 has different values in schematic and board (2.2k Ohms/2.2K)
what should I try now?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to maciv4

On 8/19/2016 1:41 PM, Jim McAuley wrote:
I would that, where do I send the files, and which files would you need?

--
To view any images and attachments in this post, visit:
https://www.element14.com/community/message/203978

Hi Jim,

Send them to support@cadsoftusa.com. Send the .brd and the .sch files.

I'll send them back once I have corrected them.

Best Regards,
Jorge Garcia
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to maciv4

On 8/19/2016 1:41 PM, Jim McAuley wrote:
I would that, where do I send the files, and which files would you need?

--
To view any images and attachments in this post, visit:
https://www.element14.com/community/message/203978

Hi Jim,

Send them to support@cadsoftusa.com. Send the .brd and the .sch files.

I'll send them back once I have corrected them.

Best Regards,
Jorge Garcia
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 rachaelp over 9 years ago in reply to maciv4

Hi Jim,

The EAGLE Central/Element14 link is currently broken. Jorge just replied on EAGLE Central so I have copied it below so you see it:

Jorge Garcia wrote:

On 8/19/2016 1:41 PM, Jim McAuley wrote:
> I would that, where do I send the files, and which files would you need?
>
> --
> To view any images and attachments in this post, visit:
> https://www.element14.com/community/message/203978
>

Hi Jim,

Send them to support@cadsoftusa.com. Send the .brd and the .sch files.

I'll send them back once I have corrected them.

Best Regards,
Jorge Garcia
Best Regards,

Rachael
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to rachaelp

On 20/08/2016 7:32 a.m., rachaelp wrote:
Hi Jim,

The EAGLE Central/Element14 link is currently broken.

Hi Rachael

Do you know for sure that Element14 has begun mirroring the EagleCentral
mirror of the Cadsoft Eagle forum. If not then it would be the Element14
interaction with the Cadsoft forum that is broken.

Warren
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to rachaelp

On 20/08/2016 7:32 a.m., rachaelp wrote:
Hi Jim,

The EAGLE Central/Element14 link is currently broken.

Hi Rachael

Do you know for sure that Element14 has begun mirroring the EagleCentral
mirror of the Cadsoft Eagle forum. If not then it would be the Element14
interaction with the Cadsoft forum that is broken.

Warren
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to rachaelp

On 20/08/2016 7:32 a.m., rachaelp wrote:
Hi Jim,

The EAGLE Central/Element14 link is currently broken.

Hi Rachael

Do you know for sure that Element14 has begun mirroring the EagleCentral
mirror of the Cadsoft Eagle forum. If not then it would be the Element14
interaction with the Cadsoft forum that is broken.

Warren
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to maciv4

Am 19.08.2016 um 19:41 schrieb Jim McAuley:
I would that, where do I send the files, and which files would you need?

--
To view any images and attachments in this post, visit:
https://www.element14.com/community/message/203978

How far is the layout?
If it is at the beginning one can think about deleting the board and
generate a new board from the schematics. This method is sometimes
faster than repairing the single errors if one is not so experimented.

--
Mit freundlichen Grüßen / With best regards

Joern Paschedag
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to maciv4

Am 19.08.2016 um 19:41 schrieb Jim McAuley:
I would that, where do I send the files, and which files would you need?

--
To view any images and attachments in this post, visit:
https://www.element14.com/community/message/203978

How far is the layout?
If it is at the beginning one can think about deleting the board and
generate a new board from the schematics. This method is sometimes
faster than repairing the single errors if one is not so experimented.

--
Mit freundlichen Grüßen / With best regards

Joern Paschedag
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 autodeskguest over 9 years ago in reply to maciv4

Am 19.08.2016 um 19:41 schrieb Jim McAuley:
I would that, where do I send the files, and which files would you need?

--
To view any images and attachments in this post, visit:
https://www.element14.com/community/message/203978

How far is the layout?
If it is at the beginning one can think about deleting the board and
generate a new board from the schematics. This method is sometimes
faster than repairing the single errors if one is not so experimented.

--
Mit freundlichen Grüßen / With best regards

Joern Paschedag
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 rachaelp over 9 years ago in reply to autodeskguest

warrenbrayshaw wrote on Fri, 19 August 2016 21:06
On 20/08/2016 7:32 a.m., rachaelp wrote:
Hi Jim,

The EAGLE Central/Element14 link is currently broken.

Hi Rachael

Do you know for sure that Element14 has begun mirroring the
EagleCentral
mirror of the Cadsoft Eagle forum. If not then it would be the
Element14
interaction with the Cadsoft forum that is broken.

Warren

Hi Warren,

You are probably right, I was just using the term mirror for convenience.

Best Regards,

Rachael

--
Web access to CadSoft support forums at www.eaglecentral.ca. Where the CadSoft EAGLE community meets.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 rachaelp over 9 years ago in reply to autodeskguest

warrenbrayshaw wrote on Fri, 19 August 2016 21:06
On 20/08/2016 7:32 a.m., rachaelp wrote:
Hi Jim,

The EAGLE Central/Element14 link is currently broken.

Hi Rachael

Do you know for sure that Element14 has begun mirroring the
EagleCentral
mirror of the Cadsoft Eagle forum. If not then it would be the
Element14
interaction with the Cadsoft forum that is broken.

Warren

Hi Warren,

You are probably right, I was just using the term mirror for convenience.

Best Regards,

Rachael

--
Web access to CadSoft support forums at www.eaglecentral.ca. Where the CadSoft EAGLE community meets.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

No Data

Different connections on R48 pin 2 and pad 2 (-12V/$$1)	2
Different connections on R84 pin 2 and pad 2 (-12V/$$1)	3