Add holes for through hole components

Question

Hi, I am new in the Eagle world and I am making a 2 layers custom board with Eagle.

I am trying to do a simple custom size board full of holes for through hole components ( a simple prototyping board) and I am not sure about which is the best way to make the holes.

I have found many resources with totally different answers. For example on this video: https://www.youtube.com/watch?v=s4-Ugi4y9lk (min: 24.00) this guy use the simple command VIA for doing this, but a VIA should be just a connection between layers. On this discussion How to add connection points for soldered wires , another guy suggest instead the library wirepad.lbr.

This is a working project. not for fun, so I need to be quite sure that I am making the righ hole. Could you someone help me? It will be really appreciate.

COMPACT · Answer

It is always best to schematic capture a PCB because it allows revisions and additions to it to be easily accomplished. For example - your Proto board - There will most likely be a stage where you want to add power rails or planes to it. Facilitating this is done easily using a schematic. There's no reason why you can't capture the prototyping area as components and have them placed on your PCB. If fact EAGLE works best in this mode because it switches between its schematic and PCB for its Design Rule Checking. I just kluged this up in moments to illustrate the point. Complete with mounting holes. The size of this board is at the maximum freeware limit.

shabaz · Answer

There are many ways to do it. The one in this photo was created by making a component for the pads. To simplify further I created a component that was a block of pads (e.g. 4x4 or whatever).

COMPACT · Answer

Firstly to create a components in a new library by: a. defining a package (which just consists of the pads of the size you want), b. defining a symbol to associate with the package, c. creating a device that correlates the pads of the package with the schematic symbol. From that create a Project and within that project create a schematic file. Place your newly defined device onto your schematic (for a proto board with no connections you won't have to define any nets), (I.e. Your schematic will just be a bunch of non-interconnected components) Then click the SCH/PCB button and allow EAGLE to create a PCB for you. Now you can move the device into the position you want on the PCB. The Schematic and PCB are closely linked allowing you to switch back to the schematic to make changes and by clicking the SCH/PCB button it'll place any new components on the PCB file. Mechanical holes don't necessarily need to be included on the Schematic and can be placed directly on the PCB.

rachaelp · Answer

Lorenz wrote on Thu, 02 March 2017 06:59 But for the pads without connections, use plain vias. They are inserted/placed in the board only. You can still connect this vias with the connect command (in the board editor - to form a GND rail for instance) Are you sure? I thought the connect command was used in the library editor to connect pads to pins in a part? I think in this case you'd want to use the name command to name any vias you wanted to be connected together to the same net or simply add them with a name already set. e.g. name 'GND' or via 'GND' I'd suggest that if you really wanted any of the holes connected you'd want to have a schematic and connect them there though rather than doing it all in the board so if this was the case the wirepad.lbr option would probably be the correct option. Best Regards, Rachael -- EAGLE support forums at http://www.eaglecentral.ca :: Where the EAGLE community meets.

geralds · Answer

Hi Angela, Holes, pad: Well, in the schematic or pcb you have 3 types of holes (round eg drilling, square eg punching, complex eg milling) that are separated into plated or non-plated holes. A via yes is, of course, also a plated hole, but its using is a bit different. In the schematic - ADD from the library, you can choose from: Holes.lbr (mounting holes, non plated or plated, round or square, or even complex special hole) Solpad.lbr (solderable pads, but this lbr is very inflexible) Wirepad.lbr (solderable pads, through holes with type of hole diameters and rings, also SMD pads) Or you can create your own lbr file with your pads or holes. If you use ADD in pcb i strongly suggest that you imports just holes, but not pads if they are will connected to an electrical contact. If you likes importing pads then make this into the schematic, also better importing the holes into the schematic. (-> consistence between schematic and pcb) The point: PAD is basically a plated hole or a SMD pad HOLE is basically a non-plated hole, is only for assembly or for the distances, e.g. for high-voltage security distance. For your project I suggest you to make your own lbr file. You can also copy the default pads into your lbr file. Please also read the manual and the tutorial. There you will find nice examples. Via: A plated hole used in the circuit board to connect through and between the layers. They can also be very flexible. If you want to connect some of the vias to a wire, you must use the command: NAME Then the menu will ask you: "this segment or complete wire" -> use complete wire! Power plane: Power planes are usually created by drawing a polygon, and then this polygon will connected to an electrical wire. (E.g. GND or VCC or VDD, .... or N $ xxx -> and if pads or vias are connected to this wire, then the polygon includes it in its calculation. Best Regards, Gerald ---

geralds · Answer

Hi, ok,,, in this way you can create your board as a component in the library. Because if you place the pads in the schematic then you can have a lot of work to sorting that on the pcb. But as a component you'll place it all directly on your defined place and they will stay it on there. Then you can draw the logo in the symbol of this pcb. Just make a defined number of pads and place it as group where ever you like. Gerald ---

autodeskguest · Answer

Angela Ameruoso wrote: Hi, I am new in the Eagle world and I am making a 2 layers custom board with Eagle. I am trying to do a simple custom size board full of holes for through hole components ( a simple prototyping board) and I am not sure about which is the best way to make the holes. depends 8-) for pads that need a connection in the schematic you can use wirepad.lib parts. They need to be i nserted in the schematic. But for the pads without connections, use plain vias. They are inserted/placed in the board only. You can still connect this vias with the connect command (in the board editor - to form a GND rail for instance) -- Lorenz

Add holes for through hole components

Top Replies