under voltage detection - Raspberry Pi 3 B+

Question

There seems to be a serious issue with the power regulator on the Raspberry Pi 3 B+, e.g.: I tried the recommended power supply, but the Pi still indicates that under voltage detected, and it keeps failing (not able to initiate anything, e.g.: sudo raspi-config, sudo apt-get update, etc.)

I bought another power supply with 5V, 3A rating, and the issues remain the same!

Can you recommend a method that I can overcome such issue(s)? Please kindly advise. Thank you.

jw0752 · Answer

Hi Si Le, Do you have a meter that you can use to verify that the voltage to the Pi is 5 volts? If possible you could also measure the current draw using the meter's ammeter. This would give you some definite ideas about where the problem lies. John

fmilburn · Answer

I picked up an inexpensive USB meters similar to the one in the link at a trade show for a couple of dollars. I've noticed them in one of the local electronics stores as well. They are accurate enough to get a reasonable idea of voltage and current and are handy at times.

luislabmo · Answer

What is the "recommended" power supply you've tried?. I've tried few good reputation power supplies in my experiments -incuding adapters for tablets which are around 2.1A-, when the Pi was running with the Touch display , I was getting the low-power notification icon until I started using the official Raspberry Pi Universal Power Supply . Another thing that may affecting the power delivery to your RPi is you USB cable. I personally would check those before concluding it is a faulty RPi case. Luis

Former Member · Answer

Hi, I had the same problem. I checked on two different power supplies. This is a cable issue! It was not until I used a short and thick cable that the error stopped. I checked three different cables.

shabaz · Answer

Hi Si Le, It sounds like a faulty Pi, if you've already tried the recommended 2.5A supply and you're running the Pi with just a keyboard and mouse attached (and no other USB devices). If you can check with another Pi 3B+, you can confirm if it is the Pi, or the supply that is faulty.

fmilburn · Answer

I agree on the USB cables - I have had problems with them in past and I think they are sometimes overlooked. Avoid the long cheap ones in particular. There is an informative video on the topic here: https://m.youtube.com/watch?v=n70N_sBYepQ&t=14s

keillrandor · Answer

I have a PI 3B +, had similar under voltage warnings, both in Debian Stretch syslog and yellow flash icon on my connected official 7" screen (I don't use any GPIO voltage bridging). I use an iFi power 2.5A rated switching PSU with micro usb connected to the PI. I also fed the screen with another separate micro usb power source. With this setup I had voltage underruns every now and then during the boot sequence. PI<----angled micro USB cable/USB-A male 0.5m---> <----micro iFi USB female A adapter/DC pin cable 0.1m---> <--DC PIN cable to iFi PSU 1.5m? ---> wall DC 230V/50Hz I resorted to solder the angled micro USB connector to the DC-pin adapter, removing about 0.5 meter of cabling and a possibly weak USB A female adapter used above. It resolved the issue. It would have been interesting to use an oscilloscope, which I don't have, to monitor the improved voltage stability.

dougw · Answer

The USB cable can easily drop the voltage by over one volt. You can see some real tests here: E36313A Triple Output DC P.S. - Review Some cables drop the voltage by over 3 volts....

You don't have permission to edit metadata of this video.

Edit media 
 
 
 
 
 
 Dimensions 
 
 
 
 x 
 
 
 
 
 Small 
 Medium 
 Large 
 Custom 
 
 
 
 
 Subject (required) 
 
 
 Brief Description 
 
 
 Tags (separated by comma) 
 
 
 Video visibility in search results 
 
 Visible 
 Hidden 
 
 
 
 Parent content 
 
 
 RE: under voltage detection - Raspberry Pi 3 B+ 
 E36313A Triple Output DC P.S. - Review 
 RE: low voltage for raspberry pi 3 
 
 
 
 
 
 
 
 
 Poster 
 
 
 
 Upload 
 Preview 
 
 
 
 
 
 
 
 
 
 
 
 
 Ok 
 
 
 
 
 
 Cancel

genebren · Answer

Doug, This is a great cable test setup. This should help all those people out there that are having under voltage errors on their Pi devices. I have switched all of my USB cables over to ANKER PowerLine products and I have not had any power delivery issues (one of my products runs >2.0 Amps through the USB cable). Thanks! Gene

rew · Answer

alinp wrote: Current limit was set to 2.2A. That's not enough. The pi will draw peaks that are larger than that. They may be very short. To catch such things, put the scope in "normal" or "single" mode and set it to trigger at 4.8V. Put the timescale to something much faster than 100ms/div. quoting shabaz and cant find the "quote" button.... The original post refers to a 5V 3A rated supply. If that really is correct, then it's not an official PSU, which is marked 5.1V 2.5A, so all bets are off if that is a measurably good PSU and cable. The original poster observed 0.4V drop so it's not surprising if an undervoltage alert occurs. IIRC, the pi4 comes with a slightly beefier power supply. 3A sounds right to me.

shabaz · Answer

Hi Roger, You're right, the Pi 4 charger is 3A, but labelled 5.1V, so still a nice way to quickly identify if people are using phone chargers, or the official chargers. I've been meaning to purchase a few of them, now that I have a couple of Pi 4's, and the BeagleBone AI use the same connector. I tried powering the BB-AI from a fairly new Samsung charger but that failed miserably. The older Pi 3 5.1V 2.5A charger is working fine for powering the BB-AI for now (using a micro USB to USB-C adapter) but I've not pushed it yet, so want the newer Pi 4 supply for that.

Former Member · Answer

As I stated on my original post, power supply with 5V, 3A is my third power supply. Haven't tried another 3B+ yet, but I thought I should seek for your help first, before running back to the store. Thanks for your response.

y2010x · Answer

Thank you all very much for your suggestions. I tried them all, but the yellow lighting bolt still showed up, and the voltage drop for most cases is about -0.4 volt. The unit is functional (not trying to reboot) in one of the power supply with the yellow thunderbolt; I ordered 3 more units to see if this is a bad unit - I will let you know the results when I have a chance to test them. Thank you all again very much.

Former Member · Answer

My issue was a USB cable .it's working fine with an OEM Samsung non fast charge box and cable. 5v 2a

dougw · Answer

Check the voltages and currents measured in this blog ... the voltage does dip enough to be worrisome with some supplies and cables.

fmilburn · Answer

To reinforce the post from Shabaz: I have a Pi 2, two Pi 3s, two Pi 3B+, and two Pi 4s. Like Shabaz I have never seen a problem with a good PSU and cable on a Pi by itself and I have loaded them up 100% for extended periods. Using a phone charger or cheap cable is the best way to see the dreaded underpower icon. Powering a screen or other add-ons with a Pi 3/3B+ off of the power pins might also cause under voltage but the Pi alone should be OK.

shabaz · Answer

glyndon wrote: The one the original post was relating: That despite a measurably-good PS and cable I'm not sure anyone has demonstrated that. As a data-point, for what it's worth, I've probably gone through a dozen official PSUs with attached cable, across different full-size Pi's (the first model, Pi 2B, Pi 2 B+, Pi 3 and 3B+, and now the 4, expect that's got a different connector) and not seen any power related issue (with the official charger+attached cable). The times I have seen a power issue, it's been resolvable by using the correct PSU or sometimes by using a thicker cable. I believe some users assume that mobile phone chargers make good power supplies for the Pi, but that's measurably not true in all cases - only sometimes. It can be demonstrated by measuring with a voltmeter, under load. The micro USB connector looks like it is designed for accepting a mobile phone charger, and there's an implicit assumption that it should work. That's not the user's fault, but nevertheless that's a common issue. A thinner cable or poor quality charger still often charges a mobile phone, but that's not the case with the Pi or other SBCs. Mobile phone chargers in conjunction with a typical charging cable, sometimes cannot supply close to 5.0V at the micro USB end when under load. The Pi's official PSU has a slightly higher output voltage to compensate for voltage drop across the cable. It's not a great implementation (there were likely non-technical reasons for that decision - i.e. cost, and the hope the standard connector could allow some mobile chargers to work under lighter loads). The Pi's official PSU makes for a terrible mobile phone charger, but is a good PSU for the Pi. The original post refers to a 5V 3A rated supply. If that really is correct, then it's not an official PSU, which is marked 5.1V 2.5A, so all bets are off if that is a measurably good PSU and cable. The original poster observed 0.4V drop so it's not surprising if an undervoltage alert occurs.

glyndon · Answer

I can supply a data point, as an example. One of my 3b+'s has been notoriously flashing undervolt alerts. So, I built, using 16ga stranded copper and new connectors, a 1m power cable, supplied voltage to it using a very expensive 5V supply rated at 400W output (it's normally intended for use in specialized equipment, e.g. medical), set its self-monitored output to 5.25v. And the blasted thing still flashed undervolt at a couple points during bootup. In fact, I did this for 3 more units, with similar results. My background across 40+ years includes a lot of electronic and electrical engineering study, so I am familiar with how current and power flows work, and have heretofore been figuring - as have others here - that the various small PSU's in use cannot handle the spiky draw by the Pi. So, I had been intending to put a 'scope on some of mine to see if that was the case. I've also considered beefing up the supply cable with some load-end buffer caps to help handle load spikes. But it seems like such drastic measures shouldn't be necessary for a device that was designed to be operated under less-than-ideal conditions (i.e. a classroom) by less than degreed engineers. Doesn't it? It's starting to sound more like there may be an actual flaw in some range of the devices, something dirt-simple like a bad batch of voltage regulators or zeners, that's frustrating a lot of otherwise adequate use-cases.

luislabmo · Answer

The voltage drop may be caused by the USB cable used: length, cable thickness, connector quality (or specs) may be the most important factors to consider: see this comment and this one . In my Raspberry Pi Road Test I cover this in the Power Consumption section . The easiest way to discard a USB power problem with the Pi is to power it directly to the GPIO with a regulated power supply where you can reduce some risk factors by increasing the wire thickness, using connectors with a good current rating, etc. USB power issues are harder to troubleshoot as USB cables are sealed most of them without reliable specs available that will bring a lot of unknown factors -one of the main reasons why is good to have the official micro USB power supply for Raspberry Pi micro USB power supply for Raspberry Pi to discard USB power issues. Luis

alinp · Answer

As stated in my original issue I've measured the voltage right at the USB input socket and it's 5.0V (so the cable drops 0.1V). The measuring procedure was done using a MSOX3104T MSOX3104T oscilloscope with a passive 10:1 probe hooked up right to the power rail smoothing capacitor C84. *schematic from the official Rasberry Pi docs . Measuring on the oscilloscope ( MSOX3104T MSOX3104T ) was done using Roll mode , at a sampling rate of 100ms/division. At no point during the testing procedure, which involved throwing multiple power hungry tasks at the CPU, did the power supply (which again was a R&S HMC8042 OS) vary by more than 100mV. Overall, the voltage did no drop under 4.9V. Despite this, the low-voltage warnings kept coming. The power was fed trough the USB port, using a high quality USB cable, that was cut to 5cm in order to expose the power and GND wires inside an hook them up to the bench PS. Given above testing procedure I can confidently exclude any factor related to the USB cable or power supply being used. Thus, I conclude that there must be a faulty hardware design somewhere down the line. If someone has identified it or has a different opinion please let me know. I still don't know if I should send in back to Farnell under warranty due to this malfunction.