Help me to setup the software to use the trimak motor

manojroy123 2 months ago

I am trying to install TMCL-IDE for windows. I am getting this error. Please help me in solving it.

Top Replies

cstanton 1 month ago in reply to manneveru +3

manneveru said: This is not right forum for this post This post is relating to a RoadTest and its consequent review, it's the correct place for it to be situated. You can turn off replies to the thread…
Jan Cumps 1 month ago in reply to manojroy123 +2

Manoj, it may help if you: use the correct name in the subject. Shows respect to the manufacturer that sponsored the board explain what step you are trying to complete in the user guide/documentation…
beacon_dave 2 months ago in reply to manojroy123 +1

https://www.analog.com/media/en/technical-documentation/user-guides/how-to-start-linux-tmcl-ide.pdf

Parents

manojroy123 1 month ago

After asking on chatgpt it says that you need to configure the motor from Wizard Pool in TMCL-IDE 4.x. But Wizard Pool is not showing any motor. Bellow is the pic of it.

How to know what has caused the error of device not detection on Wizard Pool of the TMCL-IDE 4.x
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 1 month ago in reply to manojroy123

May be relevant ?

"I found that most of my plugins were disabled.
Once I enabled them again, I was able to use the wizard."

https://ez.analog.com/motor-control-hardware-platforms2/f/q-a/599152/with-evaluation-board-tmc9660-3ph-evalv1-1-boot-setting-is-good-but-wizard-is-empty
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to beacon_dave

I have updated firmware with latest version. Still showing same problem. How to enable plugins.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 1 month ago in reply to manojroy123

Perhaps refer to the user manual for guidance.

I'd hazard a guess that they may of meant the 'Enable driver' checkbox

Presumably you completed both the power on

and the bootloader configuration settings

steps successfully before attempting to launch the Wizard Pool ?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to beacon_dave

Should the display LED on the software that is detecting voltage of the board be red for board to be detected.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to beacon_dave

UBL Bootstrapping is not showing.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
Jan Cumps 1 month ago in reply to manojroy123
Did you perform the step by step setup of https://www.analog.com/media/en/technical-documentation/user-guides/tmc9660-3ph-eval-kit-ug.pdf ?

Getting Started

IO Supply Selection

Connecting the Peripherals

TMCL-IDE Quick Start

Turn on the power supply now.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to Jan Cumps

Yes. I am using a 12 volt 8 amp power supply.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to Jan Cumps

Which driver board to select and what HW ID to set.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
Jan Cumps 1 month ago in reply to manojroy123
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

Reply

Jan Cumps 1 month ago in reply to manojroy123
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

Children

manojroy123 1 month ago in reply to Jan Cumps

But what about driver board. Which driver board should I select.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 1 month ago in reply to Jan Cumps

For motion control which board to select TMC9660-3PH-EVKIT(BOOT) or TMC9660-3PH-EVKIT(PARAM)
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel