Help me to setup the software to use the trimak motor

manojroy123 10 months ago

I am trying to install TMCL-IDE for windows. I am getting this error. Please help me in solving it.

Parents

manojroy123 10 months ago

After asking on chatgpt it says that you need to configure the motor from Wizard Pool in TMCL-IDE 4.x. But Wizard Pool is not showing any motor. Bellow is the pic of it.

How to know what has caused the error of device not detection on Wizard Pool of the TMCL-IDE 4.x
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 10 months ago in reply to manojroy123

May be relevant ?

"I found that most of my plugins were disabled.
Once I enabled them again, I was able to use the wizard."

https://ez.analog.com/motor-control-hardware-platforms2/f/q-a/599152/with-evaluation-board-tmc9660-3ph-evalv1-1-boot-setting-is-good-but-wizard-is-empty
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 10 months ago in reply to beacon_dave

I have updated firmware with latest version. Still showing same problem. How to enable plugins.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 10 months ago in reply to manojroy123

It looks like it turns red once the motor supply voltage reaches an acceptable threshold but it's the type of behaviour that would be best verified by referring to the user documentation for the TMCL-IDE.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 10 months ago in reply to beacon_dave

yes
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 10 months ago in reply to Jan Cumps

For motion control which board to select TMC9660-3PH-EVKIT(BOOT) or TMC9660-3PH-EVKIT(PARAM)
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 10 months ago in reply to Jan Cumps

But what about driver board. Which driver board should I select.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 10 months ago in reply to manojroy123

This may be relevant

and may explain why it isn't showing in TMCL-IDE device tree on the Linux version.

This may be an issue as you don't really want to commit to using the OTP just yet, and looks like the config data is lost if the board is power cycled/reset.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 10 months ago in reply to manojroy123

Perhaps need to consider resolving this first before jumping ahead to the Wizard Pool ?

There appears to be a separate tool

UblTools

that can configure the bootloader independently of the one built into TMCL-IDE

https://www.analog.com/en/resources/app-notes/an-2601.html

If nothing else, the following two commands look like they could give useful information:

Command: inspect chip

Command: inspect config
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
beacon_dave 10 months ago in reply to manojroy123

Do you mean this one ?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

Reply

beacon_dave 10 months ago in reply to manojroy123

Do you mean this one ?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

Children

beacon_dave 10 months ago in reply to manojroy123

It looks like it turns red once the motor supply voltage reaches an acceptable threshold but it's the type of behaviour that would be best verified by referring to the user documentation for the TMCL-IDE.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel
manojroy123 10 months ago in reply to beacon_dave

yes
Cancel
Vote Up 0 Vote Down

Sign in to reply

Cancel

Help me to setup the software to use the trimak motor

UblTools