Just Encase

Monitoring an irrigation canal using LoRa #5

redcharly

Hi, I'm Carlo Russo and this is the fifth part of my job. In the four blogs already made, I explained how I used the two Arduino MKR1300 boards. I have seen how to use the LoRaWAN protocol and how to manage data transfer. Then I used the two temperature…

over 3 years ago
Just Encase
Blog

Harsh Weather Monitoring Using Arduino MKR 1300 With Hammond Enclosure Case - (Blog 2)

vinayyn

In The previous Blog, I have tested the Hammond Enclosure Case using Water. The Results of the experiment concluded that the device will be not affected by the water due to its High-Quality Water and Dust Resistant Design. By taking the advantage of enclosure…

over 3 years ago
Just Encase
Blog

Monitoring an irrigation canal using LoRa #4

redcharly

Hi, I'm Carlo Russo and this is the fourth part of my work. In the past blogs I have presented the kit received, I have tried the LoRaWAN connectivity and I have added a couple of sensors to the transmitter. Today I will take care of the receiver and…

over 3 years ago
Just Encase
Blog

Biofloc Monitoring System #6: Developing the Final Firmware

taifur

We tested each sensor separately connecting with Arduino MKR WAN 1300 board. Now is the right time to develop our final code for collecting important data from all the sensors and transmitting the data to another Arduino board using LoRa. For doing so…

over 3 years ago
Just Encase
Blog

Biofloc Monitoring System #3: Collecting the Sensors & other Components

taifur

In my previous blog, I discussed the most important water parameters for a biofloc tank. I explained about temperature, pH level, ORP, and EC. In this blog, I will discuss the related sensors I am going to use for my project. Temperature Sensor …

over 3 years ago
Just Encase
Blog

Monitoring an irrigation canal using LoRa #1

redcharly

Introduction Hi, my name s Carlo Russo and this is my first blog related to the Design Challenge Just Encase. These are the components received: {gallery}Unboxing …

over 3 years ago
Just Encase
Blog

Orb-Weaver Rover - Blog #3 - Full Battery Test

milosrasic98

Orbweaver Rover - Full Battery Test Orb-weaver Rover - Monitoring and Data Collection <----- Previous Blog Table of Contents Orbweaver Rover - Full Battery Test 1. Introduction 2. Plan 3. Test 4. Results Temperature & Heat Index…

over 3 years ago
Just Encase
Blog

Orb-weaver Rover - Blog #2 - Monitoring and data collection (GCS, Sensor Boxes, GUI)

milosrasic98

Orbweaver Rover - Monitoring and Data Collection Orb-weaver Rover - Concept <----- Previous blog Table of Contents Orbweaver Rover - Monitoring and Data Collection 1. Introduction 2. LoRa communication and first tests 3. Sensor Box …

over 3 years ago
Just Encase
Blog

Particulate Matter Monitoring System for Wildfires - #4: Coding

gracemcnally

Up until now, I’ve explained the concept for my particulate matter device (Blog #1), shown the material procurement process and tested all the sensors (Blog #2), and shown the wiring and assembly for the device (Blog #3). But I haven’t talked much about…

over 3 years ago
Just Encase
Blog

[Pool Water Monitoring] #15 Collecting values and sending via LoRa: Update1 - Collecting values and sending them away... and a crazy value that was hard to track

feiticeir0

Hi all ! Hope everyone is well . Last night was time to start working on the code to collect all the data and send it away to the remote Arduino MKR 1300 WAN via LoRa . In my last post regarding the data collecting , everything is wired and working…

over 3 years ago
Just Encase
Blog

[Pool Water Monitoring] #11 Architecture Design #2: Arduino MKR 1300 WAN receiver and Grove Display

feiticeir0

Hi all ! Happy New Year 2022. Starting with the project designs, working with both Arduinos, one will collect and send information, and the other one will receive and display it. The following blog entry explains the project design Data receiving…

over 3 years ago
Just Encase
Blog

Particulate Matter Monitoring System for Wildfires - #2: Material Procurement and Sensor Testing

gracemcnally

Now that I have a concept for my project and have done background research on particulate matter (PM), the next step was material procurement. The Hammond Manufacturing Enclosures and Arduino MRK WAN 1300’s were coming in the mail along with the Grove…

over 3 years ago
Just Encase
Blog

[Pool Water Monitoring] #7 LoRa Communication between Arduino MKR 1300 WAN and Arduino MKR 1300 WAN

feiticeir0

Hello everyone. Hope you're all safe . After I received the kit and been able to read temperature values from the probe with one MKR 1300 WAN , today was time to try and start a conversation, using LoRa, between those two modules. Hardware 2x…

over 3 years ago
Just Encase
Blog