Hello allHere is an update as to what is going on with this project... When I connect the RA8875 to the MKR, here are the specifics for communications (that work):// Connect SCLK to MKR1000 #09 (Hardware SPI clock)// Connect MISO to MKR1000 #10 ...
Analyse the Spectrum with ArduinoFFT1. The ISD1820 is microphone module, the analogue value shall be turned into digital value for processing purpose. Pin A0 is set as INPUT, fetching data form ISD1802.int inputPin = A0;The following codes do t...
IntroductionHi! In this update I will be taking a look at connecting a capactive fingerprint module to an Arduino MKR1000. I looked all over online, and could only find optical fingerprint sensors being connected to the Arduino, so I thought, why not...
<<<<Previous BlogNext Blog>>>> Audio & Visual Cue System for Anosmia (Smell Disorder) and Smart WheelChair - Ft. Amazon's AlexaWeek 6: Aug 7 - 13 The Smart Wheelchair h...
With Dan returned from his vacation, we had a meeting to integrate all the code we had written so far, work on the circuitry, and begin the design for the case that will house the device when it is done. The code went together easily enough, though t...
#Blog5Hello Everyone! Happy Independence Day Its August 15, we celebrate Independence Day in our country. Here is my work on integrating SD Card Shield and PAM8403 Audio Amplifier to Arduino MKR1000. Which is the part of "Smart Voice ...
1. Selection of WhistleThe most important part of the project is the whistle. Unlike BLE, WIFI or other remote control parts, the whistle do no need any power to keep it alive. You may think they are different, but to users, it is the same. Therefore...
Welcome to our fifth blog post! This blog will be a little short, as we're essentially posting an update on the last blog. We mentioned the Show and Tell model in that blog, and talked about its structure and capabilities of the model. We al...
I came home from work, and there was a large box sitting on my chair. My first thought was "Wow, that is big." That thought must have actually come out, because my wife said, " yeah, I thought that it was bigger than you were expecting...
<<<<Previous Blog Next Blog>>>> Audio & Visual Cue System for Anosmia (Smell Disorder) and Smart WheelChair - Ft. Amazon's Alexa
Week 5: July 31 - Aug 6
Table of Contents
...
Table of Contents
Introduction
Video
Steps - Blueprints
Steps - Alexa App
Introduction This blog explains how to customize your conversation with Amazon Alexa using Blueprints and enable it for your Alexa which can be a...
Table of Contents
Introduction
Video
Alexa App - Explained
How to Set up a new Device
How to Change Language
Introduction This blog provides an overview of the Amazon Alexa app, how to connect it with an Alexa e...
#Blog4 Hello Everyone Getting Started with Arduino MKR 1000Hello Everyone! Voltage Divider Circuit to measure the Bending and a LED indication In this below Demo, on detecting the bending of the flex sensor, a LED will glow ...
For my 5th blog posting I will show the code I am using to run the robot and spelling in Braille. This part has been a bit of work but is coming along great. I have run into issues with the motors I have for driving the robot but that will be discuss...
Hello everyone. I was able to get the Adafruit RA8875 to work with the MKR1000.I was recently able to get the VS1053 (Adafruit Music Maker MP3 Shield) to work with the MKR1000.The issue is when I connect them together with the MKR1000, I cannot get t...
One of the things our device will need to accomplish is reading a wave file (the pre-recorded help message) from the SD card and playing it back so that it can be used by the GSM module, which expects an analog waveform. While it has historically bee...
IntroductionHi! This will be my third update for this challenge, in the last update I made first steps in trying to make the slider mechanism for the skeleton key. For this update I will be taking a look at the center of the project, the Arduino MKR1...
Welcome to our fourth blog post! Today we'll be looking at a potential model for our use-case, the Show and Tell model.The Show and Tell model is a neural image caption generator- It is a deep neural network that learns how to describe the conten...
Hello everyone! I received my Adafruit MP3 Shield yesterday late and was able to solder the connectors and test my Wav files! Worked like a champ with the speakers I took from a broken laptop. I also was able to finish the boxes on the TFT ...
#Blog3 Hello Everyone Got received other pending parts!Let’s begin the basic element that required to capture the Gesture.Gestures are the physical actions that convey some meaningful information. It includes movement of the hands. The pr...
For my 4th blog I will be showing how I attached the motors to drive the robot as well as the wiring I started for the Arduino. For the motors, I picked up a couple of kits with gears so I can get the speed down and torque up. The gear ratio is ...
