1. Create a Project from Template Application 2. Modify Code 2.1 Modify WiFi Configuration 2.2 Modify MQTT Configuration 2.3 Certificate and Private Key Configuration 2.4 Modify Functional Code 3 Test the Code 3.1 Create MQTT Topic Subs...

Testing the sensors:Here I will be testing the required sensors for the project and then I will be integrating them to help me detect the health of the package.Motion sensor BMI160.[I will be using the Cypress CY8CKIT-028-TFT module as it had the BMI...

1 Make the Prototype Work 2 Start the Project 3 Connectiong with the Board with Mobile BLE app 4 More to do 1 Make the Prototype WorkThere have been times working on Clock conflics, the PDM depends on PLL clock and FreeRTOS make its own clock...

My new findings on ZMOD4510 Air Quality SensorZMOD4510 Air Quality Sensor is focused on the outdoor air quality measurement based on ozone and NOx concentration. Ozone concentration indoor is very low. I was able to detect it after a long period of t...

It's hard to believe that we've already reached the end of the 10 week design challenge period.  As always with these challenges, I've learned a lot and had a great time.  Thanks to Infineon and E14 for the opportunity and the dev board.&nb...

First things first:Compile the hello world and get the required things like sensors and battery etc. Before compiling we need to add the compiler path in the environmental varibles:CY_TOOLS_PATHS = C:/Infineon/ModusToolbox/tools_2.4/Remember forward ...

Hello all,        It's been quite a while I had received the hardware and I was going through a lot of documentation and figuring my way out to get the required things to be done,before starting the project, i.e...

Posts in this projectPallet Tracker - 01 - Project descriptionPallet Tracker - 02 - Development environmentPallet Tracker - 03 - Application skeletonPallet Tracker - 04 - PSoC6 power modes and LPCompPallet Tracker - 05 - Evaluating power consumptionP...

Hi Everyone,In the last (blog4) i have setup the wireless charging unit for smart composer. In this blog the final demo is explained. Introduction:People use composter in their garden to compost the organic waste into bone material which helps t...

1 Bluetooth LE introduction 2 Create Android APP 4 To Make the BLE Drum work 1 Bluetooth LE introductionBluetooth LE-enabled devices to transmit data between each other, first form a channel of communication. There are following Key term shall ...

1. Set up AWS Account 2. Create A Thing  1. Set up AWS Account Creating AWS account is very easy. Just follow the instruction here. Since I already have an AWS account, I won't show the steps how to set up the account.2. Create A Th...

Table of ContentsWearable Gesture Control - #1 IntroductionWearable Gesture Control - #2 Install & Setup Template ApplicationWearable Gesture Control - #3 Integrating LCD & AccelerometerWearable Gesture Control - #4 Collecting data for Edge I...

1. Hardware Connection 2. Software Project  1. Hardware Connection Water level sensor from Anndason, model# DP5200 is used to detect the water level in the sump pit. Basically it's a float switch. When water is rising, it pushes the...

In my previous post Low Power IoT Design Challenge - WLAN Low Power , I had taken some current measurements of my project running prior to any attempts at power reduction. I had also tried the WLAN Low Power example that uses the Low Power Assistant ...

Hi Everyone, In the last blog (blog3) i explained about the cloud connectivity and Alexa skills testing. In this blog explain about the power supply and wireless charging system. EnviroCycle Composter:This EnviroCycle Composter (https://www...

Work In ProgressPlease note that this blog post is still a work in progress. I've used CTRL+S shortcut to save the draft, but instead of saving it as a draft, the blog got published. AnyCloud_BLE_Environmental_Sensing_ServiceI've importe...

         BLOG# 5 - BPM Display - Conclusion and Future EnhancementsA Heart Rate Monitor Display project utilizing the PSoC™︎ 6S2 + AIROC™︎ Wi-Fi/Bluetooth Pioneer Kitmanufactured by CYPRESS - INFINEON TECHNOLOGIES (Pa...

          BLOG# 4 - BPM Display - System Implementation and TestingA Heart Rate Monitor Display project utilizing the PSoC 6S2 + AIROC Wi-Fi/Bluetooth Pioneer Kitmanufactured by CYPRESS - INFINEON TECHNOLOGIE...

I've gotten the basic functionality of my Secure Entry project working, so it's time to look at implementing the "low power" element.  Modus Toolbox provides the capability to implement low power applications of the PSoC 6 with...

Hi Everyone, In the last blog (blog2) i explained about the interfacing sensors and displays. In this blog is about the cloud connectivityfor Smart Composter over MQTT. MQTT:MQTT is the widely used protocol for publishing and subscribing th...

In this blog, I will show you how to deploy the SensiML model into the PSoC6 target. In the previous blog, I showed you how to download the SensiML knowledge pack for the M4 microcontroller. After downloading the knowledge pack you need to unzip the ...

1. ModusToolbox Installation Update KitProg3 Firmware 2. “Hello World” Application Create a New Application Serial Terminal inside IDE Build & Run Application  1. ModusToolbox Installation I use Linux machine for most of my ...

I've realized that I'm not sufficiently up the learning curve with the PSoC6 and Modus Toolbox to attempt to implement vision processing on the PSoC6 in the timeframe of the design challenge.  I have been trying out different "intelligent" camer...

Hi Everyone, In the last blog (blog1) i explained about the overall concept and designs. In this blog i write about how i have interfaced sensors whichrequired for this "Smart Coposter".  Total Three sensing part in this design and 3 s...

Posts in this projectPallet Tracker - 01 - Project descriptionPallet Tracker - 02 - Development environmentPallet Tracker - 03 - Application skeletonPallet Tracker - 04 - PSoC6 power modes and LPCompPallet Tracker - 05 - Evaluating power consumptionP...